i was looking for low cost gps to pc time setting...possible portable op's what i found and am testing with is a rcvr... www.amazon.com/dp/B01EROIUEW?psc=1&ref=ppx_yo2ov_dt_b_product_details $15 softw

Hi I have been using the FT100D with the G4ZLP interface for WSJTX, which works very well. I use it mainly for 6 2 and 70cm FT8 mainly during the spring and summer when conditions are best for Sporadi

My Icom 7300 will shut down and I will get the following error messages on my computer. These messages appear on my Dell Windows 7 desktop and my HP Windows 11 Laptop. I don't know if the problem is w

In North America, should I be tuning to 5.2870Mhz to be receiving 60m WSPR from NA and overseas, or are the frequencies different? And how do I get that frequency loaded in WSJTX so I can select it in

I have an IC7300 and installed Win4icom and have that setup. I also installed OMNIRIG and com0com and Omnirig is communicating with Win4icom. When I open WSJTX and set up omnirig1 it fails to Failed t

I read thru the Logging portion of the WSJT-X manual. Did not find an answer. Where is a description explaining the parts of the comma delimited wsjtx.log file? Thanks.

What causes "interference" lines in a regular pattern on the wsjt-x waterfall? They eventually go away, they do not stop making QSOs, and in my case are more likely to occur in the AM. Just irritating

I have been using WSJT-X for several years, primarily with my TS-890S. I have another copy on a laptop to run VHF/UHF with Icom 9700. For some reason, when I click on a station in the left panel, the

i am trying to run VaraC which needs comm5 in my configuration. varac reports comm5 in use. i have no other program using comm5 besides wsjt. i've tried everything to get this comm port released to no

The Perdue download page times out now for two days. Has the download source link moved? 73, Duane AC5AA

I have the WSJT software up and running on the MacMini and the mac connected to the Icom 7600 via USB. I see receive signals but when I click on CAT I get a list of errors. I tried various settings bu

Installed WSJT-X (2.5.4 and then 2.6.1) on a new Dell Inspiron for use with FT-991A. Settings the same as on older Samsung laptop. On the Dell I see no signals and the volume slider (lower left of WSJ

Ok, running Win10, v2.6.0 GA on a known well running system. I have noticed that many times the DECODE button is illuminated and stuck on throughout an entire TX cycle; until the next RX cycle is fini

Greg, You could make a bootable USB with whatever “flavor” of Linux you want to try. Then boot it up and give it a whirl. I’ve done this on a few different ones, I chose MX21, or it chose me. I run WS

If you choose "NA VHF" contest, it defaults to "PACC", as I found out today in the January VHF SS. I can easily clear that out, but if I switch out of contest mode to reply to a station that's not usi

What causer a hamlib bus error while transmitting signals? Tuning works fine. PTT works, rig control works.

I'm new to Ham Radio and trying to get WSJTX working correctly on an Apple Silicon (M1) laptop. I have the Silicon Labs CP210x Drivers installed and the CAT seems to be working to my Yaesu FT-710. How

V: 2.5.4 - Win 10 Ran the Cab file generator after contest, tried unsuccessfully several times to upload it to ARRL log submissions. Kept getting this message: "Sorry! We're unable to accept your log.

I attempt to download WSJT-X version 2.6.1 from SourceForce. AV automatically blocks and removes the downloaded file from my PC due to WS.Reputation.1 threat. "Threat type: Insight Network Threat. The

There are 36 WD sites listening for some or all FST4W modes on 2200-10M. Since Gywn G3ZIL has determined that WSPR-2 signals interfere with reception of FST4W signals only when the WSPT-2 signal is +8