|
locked
sticky
V2.2.2 staggered decoding 3 messages
Hi - been away from WSJT-X for a while. Just installed v2.2.2 on my MacBook Pro, running OSX Catalina 10.15.6. I’m using an Elecraft KX2. I am seeing something very different on the decode process tha
Hi - been away from WSJT-X for a while. Just installed v2.2.2 on my MacBook Pro, running OSX Catalina 10.15.6. I’m using an Elecraft KX2. I am seeing something very different on the decode process than what I had seen on previous versions - several months ago. When on FT8, the progress bar goes across almost to completion, and a bunch of decoded signals display in the left panel. Then, the decode button turns off, then back on and several (usually 2-3) more signals are shown in the last panel. The older version didn’t do that - when it was done decoding, it was done, period. Where this causes an issue is when that left panel is almost full at decode time. Just as I’m about to double click on a station to call, those last few lines pop up on the screen, moving the one I was going to call up a few lines. Do I have something set incorrectly in the preferences that causes this? Jim Bennett / W6JHB Folsom, CA
By
Jim Bennett
·
|
|
locked
sticky
Trouble launching WSJTX on Mac 64bit os 10.12.6 5 messages
#mac
Hello everyone. I just joined this group today and have a question that hopefully can be answered. Please forgive me if this has already been covered; I tried to find documentation on this issue witho
Hello everyone. I just joined this group today and have a question that hopefully can be answered. Please forgive me if this has already been covered; I tried to find documentation on this issue without any success. The download and install of the program went just fine. However when I try to launch the program I get 2 error messages about shared memory. I have attached screenshots below. Does anyone know why this is happening and a possible remedy for it? Thanks, Michael Rieger KJ7BRM
By
thedivemen@...
·
|
|
locked
sticky
Error while opening the program: (invalid ADIF header). 5 messages
#BugReport
I am looking for solution for this error. wsjt version x 2.2.2. windows 10 64 bit operating system. error while opening the program: (invalid ADIF header). when i open the program i get this error eve
I am looking for solution for this error. wsjt version x 2.2.2. windows 10 64 bit operating system. error while opening the program: (invalid ADIF header). when i open the program i get this error every time i open it. error photo attached. Thank you so much.
By mattia iu2cgb
·
|
|
locked
sticky
Ubuntu 20.04 Compiling From Source 8 messages
#linux
Hello, My first attempt at a build from source. I have done my best to search for an answer but no luck. My system is Xubuntu 20.04.1 Thank you for any help, My problem: -- Building for for: Linux-x86
Hello, My first attempt at a build from source. I have done my best to search for an answer but no luck. My system is Xubuntu 20.04.1 Thank you for any help, My problem: -- Building for for: Linux-x86_64 -- ****************************************************** -- Checking for module 'hamlib' -- Package 'libusb-1.0', required by 'hamlib', not found -- Found hamlib CMake Error at /usr/share/cmake-3.16/Modules/FindPackageHandleStandardArgs.cmake:146 (message): Could NOT find hamlib (missing: hamlib_LIBRARY_DIRS) (Required is at least version "3") Call Stack (most recent call first): /usr/share/cmake-3.16/Modules/FindPackageHandleStandardArgs.cmake:393 (_FPHSA_FAILURE_MESSAGE) CMake/Modules/Findhamlib.cmake:88 (find_package_handle_standard_args) CMakeLists.txt:875 (find_package) -- Configuring incomplete, errors occurred! See also "/home/zx20/build/build/wsjtx-prefix/src/wsjtx-build/CMakeFiles/CMakeOutput.log". make[2]: *** [CMakeFiles/wsjtx-build.dir/build.make:68: wsjtx-prefix/src/wsjtx-stamp/wsjtx-configure] Error 1 make[1]: *** [CMakeFiles/Makefile2:442: CMakeFiles/wsjtx-build.dir/all] Error 2 make: *** [Makefile:84: all] Error 2 This looks like I need to find libusb-1.0 Thank you , Stan, KA1ZE
By Stan
·
|
|
locked
sticky
Windows audio
#FT4
#FT8
#txaudio
For those, who like me, have had issues with Windows 'messing' with the USB/audio there is a very interesting article that explains whats going on. Its called USB soundcards and is in the Data section
For those, who like me, have had issues with Windows 'messing' with the USB/audio there is a very interesting article that explains whats going on. Its called USB soundcards and is in the Data section of RSGB magazine - Feb 2021. Basically, it explains that every time a USB device is plugged in a 'note' is made This record is added to each time another/same device is plugged in. This can lead devices not being registered correctly in favour of the 'default' devices. Hope this is useful. Regards - Phil (G0DOR)
By Phil Davidson
·
|
|
locked
sticky
Mac M1 Memory Error 13 messages
Hello everyone, After 30 years without a mac - my last and only one was the Mac SE - I took the leap and bought the Mac M1 Mini. I am proficient at running wsjt-x on Windows and Linux. I cannot get Ws
Hello everyone, After 30 years without a mac - my last and only one was the Mac SE - I took the leap and bought the Mac M1 Mini. I am proficient at running wsjt-x on Windows and Linux. I cannot get Wsjt-x to even run. This is the error messages I get before it crashes. I have run the apple diagnostic program and it found no errors. Help would be appreciated. Ken w6bzy
By Ken Hendrickson
·
|
|
locked
sticky
Set WSJT-X To Turn On My Radio 4 messages
#Cat_RigControl
Since installing 2.3.0 rc3, I no longer see my radio being automatically turned on by WSJT-X - how do I make that happen again? -- 73, Patrick, W6AJR
Since installing 2.3.0 rc3, I no longer see my radio being automatically turned on by WSJT-X - how do I make that happen again? -- 73, Patrick, W6AJR
By Patrick Hung
·
|
|
locked
sticky
Windows audio and sleep mode 11 messages
#AudioIssues
When my PC turns the screen off (not sleep mode), and then wakes up again, WSJT receives OK. But when I try to transmit, the CAT/PTT stuff works OK, but no audio is sent to the rig. I have to restart
When my PC turns the screen off (not sleep mode), and then wakes up again, WSJT receives OK. But when I try to transmit, the CAT/PTT stuff works OK, but no audio is sent to the rig. I have to restart WSJT to actually transmit a signal. I just changes PCs, and this didn't happen with my previous PC. Both were running Win10 through a microKeyerIII to a Yaesu FTDX101. This may be more of a PC question... I just don't know where to look... Thanks, Frank W2YK
By Frank W2YK
·
|
|
locked
sticky
Setting Windows WSJT-X Tx audio levels (ALL VERSION 2 VERSIONS)
#txaudio
This document was originally posted by Bill, G4WJS as part of a long thread. Assuming you are running on MS Windows and have installed WSJT-X, this explains how to set Tx audio levels correctly: The i
This document was originally posted by Bill, G4WJS as part of a long thread. Assuming you are running on MS Windows and have installed WSJT-X, this explains how to set Tx audio levels correctly: The issue you may have with Windows WSJT-X Tx audio levels is due to the "Pwr" slider in WSJT-X no longer being linked to the Windows mixer control for the Tx audio device. This means that you must set the mixer slider manually, this should be a one-time operation. Setting the mixer control is a two step operation. Firstly you must set the mixer control to maximum. The mixer control is only visible when transmitting so use the "Tune" button in WSJT-X. It is advisable to reduce the "Pwr" slider in WSJT-X to minimum while doing this to limit the output power, or do this part with the rig switched off. The mixer slider will look something like this: Once the mixer is set to maximum the second step is very important. You must now adjust the master level for your Tx audio device to 0dB. The level control for that is in the audio playback device properties for the Tx audio device which looks like this: If your slider scale is not in decibels then right-click the slider and select decibels. Your audio device may not have gain, in which case 0 dB will be fully to the right. Some devices do have gain, *in those cases it is critical that the gain be reduced to 0 dB* otherwise a severely distorted transmit signal will be produced. Once you have completed this one time setup you can increase the "Pwr" slider back to maximum for full level audio output from WSJT-X. I recommend rechecking your Tx levels elsewhere, e.g. data modulation level adjustments on your rig, audio interface level controls etc. to ensure that you are not over-driving the audio input of your rig. A good method is to use a 1,500 Hz Tx audio offset "Tune" tone with the " ;Pwr" slider at maximum and your rig at maximum power into a good dummy load. With that arrangement reducing the interface or rig's data modulation input level until little or no ALC is indicated on the rig is about right and should give around 90% of the maximum output of your rig. If your interface and rig do not have any Tx audio level controls then it is OK to use the operating system audio device master level control as shown above to reduce the audio level to a correct amount *so long as the critical 0 dB level is never exceeded*. Once this setup is complete you can make routine Tx power adjustments using power control on the rig or the "Pwr" slider in WSJT-X. Bill G4WJS. It is also advisable to prevent windows USB interfaces from being place into power save mode. The instructions are here. Don't forget to include HDMI interface as they also utilize audio. http://www.dxlabsuite.com/dxlabwiki/PreventUSBPortPowerDown
By groups@...
·
|
|
locked
sticky
#special Updated group format and rules 13 messages
#special
Happy New Year . January 2021 marks the first anniversary of this group's merger with the old WSJT Yahoo group. The merger went quite well. I tried to minimize group rules and overall members have bee
Happy New Year . January 2021 marks the first anniversary of this group's merger with the old WSJT Yahoo group. The merger went quite well. I tried to minimize group rules and overall members have been remarkable respectful and insightful in their posts. I have had a few concerns reported to me and a review of those concerns has prompted a few changes, effective immediately. No personal insults, be polite when expressing opinions that differ from others. No items "for sale" . No expression of political viewpoints, keep the messages focused on the software. This is a worldwide group made of many different cultures, faiths, values, and ethnic groups. Please exhibit tolerance, respect and kindness. Threads that become expansive or begin to form a circular argument may be moderated or "locked" by moderators after a period of time so that they do not dominate the group. No promoting the use of the WSJTX software in a manner that violates the author's copyright terms. Moderating staff exercise exclusive discretion over all posted content, Please report any message that you feel moderating staff may have missed and required a review of possible inappropriate content. Please note we have had a few concerns where people assume that myself and other moderators are part of the WSJT-X development team. That is not the case. We are totally independent of that team. Members of the team do use this group and some even reply to questions. Please be aware that the development team members respond as a courtesy and are under no obligation. In addressing moderators and members of the development team , please keep the ethos of "open source" software. That includes Transparency, Collaboration, Community. The moderators and some of the development team have had "demands" placed on them from a handful of users who seem to expect the same level of accountability as one would expect from a tort duty or relationship. Effective immediately "tags" are required for each post. This will help address the concerns some members have expressed about topics being repetitive and some members failing to use the search feature before posting a question. Hashtags also help us with moderator duties. If you would like to serve as a moderator please email me at k3ukandy@... To serve as a moderator you must have been a member of this group for at least one year. Moderators from Oceania would be especially welcome. I wish you all peace and good health in 2021 Andy K3UK Owner
By Andrew OBrien
·
|
|
#WSPR - band hopping
#WSPR
Hello- win10, updated. using wsjtx v2.4.0-rc4 for wspr monitoring. appears band hopping not working? the "day part" does not show in bottom row of display. also when i look at the 'schedule' , top row
Hello- win10, updated. using wsjtx v2.4.0-rc4 for wspr monitoring. appears band hopping not working? the "day part" does not show in bottom row of display. also when i look at the 'schedule' , top row
|
By d_ziolkowski
·
|
|
#bugreport (more a suggestion?): stop auto scroll when scroll bar is not at bottom
#BugReport
Hello all of you, I am a new user of wsjt-x (first as an SWL [NL413] and in the near future as pe1atn). Last Saturday the PACCDigi contest was happening. It was my first contest. So used wsjt-x (v2.3.
Hello all of you, I am a new user of wsjt-x (first as an SWL [NL413] and in the near future as pe1atn). Last Saturday the PACCDigi contest was happening. It was my first contest. So used wsjt-x (v2.3.
|
By Victor Reijs
·
|
|
OpenAcc programmer?
#WSPR
Are there any OpenACC programmers here to might take a look at the standalone program daemon WSPRD that does the WSPR decode.? I am hoping that there may be an opportunity to move much of wsprd to GPU
Are there any OpenACC programmers here to might take a look at the standalone program daemon WSPRD that does the WSPR decode.? I am hoping that there may be an opportunity to move much of wsprd to GPU
|
By John
·
|
|
Can't move forward! 9 messages
#Cat_RigControl
#NewUser
#WSJTX_config
Well, I finally got the waterfall to show up. I am waiting for my new Digimode-4 to show up any day now, hoping THAT will be a logical upgrade from the U5 Link; until then, I need some help. I can't r
Well, I finally got the waterfall to show up. I am waiting for my new Digimode-4 to show up any day now, hoping THAT will be a logical upgrade from the U5 Link; until then, I need some help. I can't r
|
By Tony Castelli
·
|
|
USB MODE 2 messages
#FT8
My FT-891 goes into D-U mode when running WSJT-X. I cannot force FT-891 into USB. What in WJST-X is forcing the FT-891 into the D-U mode? HELP!!
My FT-891 goes into D-U mode when running WSJT-X. I cannot force FT-891 into USB. What in WJST-X is forcing the FT-891 into the D-U mode? HELP!!
|
By Michael Optie
·
|
|
moderated
IC-7300 sudden CAT issue 4 messages
#AudioIssues
#bluetooth
#BugReport
#Cat_RigControl
I'm stumped and can't find anything about this issue after a lot of googling. I'm on Windows 10 on an ASUS laptop and my rig is an IC-7300. Suddenly, when I attempt to transmit (FT8) with my IC-7300,
I'm stumped and can't find anything about this issue after a lot of googling. I'm on Windows 10 on an ASUS laptop and my rig is an IC-7300. Suddenly, when I attempt to transmit (FT8) with my IC-7300,
|
By Mike Cummings
·
|
|
#bugreport ALL.TXT 9 messages
#BugReport
Team: I am noticing that under some conditions, the date field is omitted from ALL.TXT for monitored calls, but not for transmissions I make. What is a little more odd, this did happen when switching
Team: I am noticing that under some conditions, the date field is omitted from ALL.TXT for monitored calls, but not for transmissions I make. What is a little more odd, this did happen when switching
|
By Bill Lederer
·
|
|
Using radios for wajtx and remote 5 messages
#Cat_RigControl
Good afternoon. I got my income 7300 and 9700 set up and working again but forgot to check output power, which turns out to be zip. I went ahead and worked on the icom res-ba1 software and got that wo
Good afternoon. I got my income 7300 and 9700 set up and working again but forgot to check output power, which turns out to be zip. I went ahead and worked on the icom res-ba1 software and got that wo
|
By Gerald Klotz
·
|
|
Q65 in less favourable condx? 17 messages
#Q65
Hi folks Some advice please. At present I am working Q65a 30 seconds from Scotland GM into mainland Europe. Running a home brew 2 ele and 80 watts. Using the ON4KST chatroom I know guys are listening
Hi folks Some advice please. At present I am working Q65a 30 seconds from Scotland GM into mainland Europe. Running a home brew 2 ele and 80 watts. Using the ON4KST chatroom I know guys are listening
|
By johnsherry57
·
|
|
#FST4 Coding On a PIC
#FST4
A brief update on progress. PIC code for the later generation enhanced device, the 16F1827, now exists that will turn 13 characters of Plain text, or 17.75 Hex characters into a set of symbols ready t
A brief update on progress. PIC code for the later generation enhanced device, the 16F1827, now exists that will turn 13 characters of Plain text, or 17.75 Hex characters into a set of symbols ready t
|
By Andy TALBOT
·
|