locked (WSJTX) WSJT-X Not Working on New Windows 11 Computer #windows11 #install


Stan Galonski
 

All, My old setup was a Windows 10 desktop, Signalink usb, Yaesu FTDX5000 and running HRD as the logging program all worked well with 1,000's of QSOs logged. I upgraded my Desktop to a Dell Inspiration 3900 running Windows 11, I can't get WSJT to work, no stations show in Band activity or the Graph, Tune will show 100 watts then drop to 35 watts after 5 seconds. I can Log a dummy QSO and it will show on the HDR log.  I have set up WSJT and HRD per their manual, HDR seems fine unless I start WSJT first then I get a "com 3 in use by another program". 
 I am at a total loss on what to do next.
 73, StanKK3KK


Dennis W1UE
 

Stan

My best advice- get wsjt-x to work first. If wsjt doesn’t work, then the
two programs won’t work.

Once that works, add in HRD.

Dennis W1UE

On Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

All, My old setup was a Windows 10 desktop, Signalink usb, Yaesu FTDX5000
and running HRD as the logging program all worked well with 1,000's of QSOs
logged. I upgraded my Desktop to a Dell Inspiration 3900 running Windows
11, I can't get WSJT to work, no stations show in Band activity or the
Graph, Tune will show 100 watts then drop to 35 watts after 5 seconds. I
can Log a dummy QSO and it will show on the HDR log. I have set up WSJT
and HRD per their manual, HDR seems fine unless I start WSJT first then I
get a "com 3 in use by another program".
I am at a total loss on what to do next.
73, StanKK3KK






Stan Galonski
 

Dennis,
 That's the issue, trying to get it to work with just the rig. Followed the setup procedure  and no signal decodes? StanKK3KK

In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time, egan.dennis88@... writes: 
Stan My best advice- get wsjt-x to work first.  If wsjt doesn’t work, then thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1@...> wrote: > All, My old setup was a Windows 10 desktop, Signalink usb, Yaesu FTDX5000> and running HRD as the logging program all worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a Dell Inspiration 3900 running Windows> 11, I can't get WSJT to work, no stations show in Band activity or the> Graph, Tune will show 100 watts then drop to 35 watts after 5 seconds. I> can Log a dummy QSO and it will show on the HDR log.  I have set up WSJT> and HRD per their manual, HDR seems fine unless I start WSJT first then I> get a "com 3 in use by another program".>  I am at a total loss on what to do next.>  73, StanKK3KK>>> >>>


Michael Black
 

Look in services for "WAV" audio items.  Disable them.  I believe  there are two of them.
Mike

On Tuesday, October 4, 2022 at 04:25:22 PM CDT, Stan Galonski via groups.io <sgalonski1@...> wrote:

All, My old setup was a Windows 10 desktop, Signalink usb, Yaesu FTDX5000 and running HRD as the logging program all worked well with 1,000's of QSOs logged. I upgraded my Desktop to a Dell Inspiration 3900 running Windows 11, I can't get WSJT to work, no stations show in Band activity or the Graph, Tune will show 100 watts then drop to 35 watts after 5 seconds. I can Log a dummy QSO and it will show on the HDR log.  I have set up WSJT and HRD per their manual, HDR seems fine unless I start WSJT first then I get a "com 3 in use by another program". 
 I am at a total loss on what to do next.
 73, StanKK3KK


Dennis W1UE
 

Stan
Do any signals show in the waterfall? If not,
Then either
1. Wrong sound card selected
2. Wrong sound card input selected
3. Input to the sound card not adjusted correctly.
4. If you have a USB sound card available, try using it
5. Does your computer have separate jacks for headphones and microphone?

Dennis W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
That's the issue, trying to get it to work with just the rig. Followed
the setup procedure and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first. If wsjt doesn’t work, then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10 desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no stations
show in Band activity or the> Graph, Tune will show 100 watts then drop to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on the
HDR log. I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".> I am at a total loss on what to do next.> 73, StanKK3KK>>>





Dennis W1UE
 

Stan
You also need to check the Windows-Settings-Sound to make sure that what
you want is accurately in there. This is in addition to having wsjt
configured correctly.

Dennis
W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
That's the issue, trying to get it to work with just the rig. Followed
the setup procedure and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first. If wsjt doesn’t work, then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10 desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no stations
show in Band activity or the> Graph, Tune will show 100 watts then drop to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on the
HDR log. I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".> I am at a total loss on what to do next.> 73, StanKK3KK>>>





Stan Galonski
 

Not sure what you mean Windows sound setting?

In a message dated 10/4/2022 3:25:51 PM Pacific Standard Time, egan.dennis88@... writes: 
Stan
You also need to check the Windows-Settings-Sound to make sure that what
you want is accurately in there.  This is in addition to having wsjt
configured correctly.

Dennis
W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
  That's the issue, trying to get it to work with just the rig. Followed
the setup procedure  and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first.  If wsjt doesn’t work, then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10 desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no stations
show in Band activity or the> Graph, Tune will show 100 watts then drop to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on the
HDR log.  I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".>  I am at a total loss on what to do next.>  73, StanKK3KK>>>





Stan Galonski
 

1. Wrong sound card selected  -  using Signalink USB - how would I select it?
2. Wrong sound card input selected -   set to both set to usb audio codex
3. Input to the sound card not adjusted correctly. -   how is this set?
4. If you have a USB sound card available, try using i-  using Signlink USB
5. Does your computer have separate jacks for headphones and microphone? -   Yes

 Like I stated the exact setup was working on my old windows 10 system StanKK3KK

In a message dated 10/4/2022 3:21:41 PM Pacific Standard Time, egan.dennis88@... writes: 
Stan
Do any signals show in the waterfall?  If not,
Then either
1. Wrong sound card selected
2. Wrong sound card input selected
3. Input to the sound card not adjusted correctly.
4. If you have a USB sound card available, try using it
5. Does your computer have separate jacks for headphones and microphone?

Dennis W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
  That's the issue, trying to get it to work with just the rig. Followed
the setup procedure  and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first.  If wsjt doesn’t work, then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10 desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no stations
show in Band activity or the> Graph, Tune will show 100 watts then drop to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on the
HDR log.  I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".>  I am at a total loss on what to do next.>  73, StanKK3KK>>>





Stan Galonski
 

Disabled both -- no change

In a message dated 10/4/2022 3:13:04 PM Pacific Standard Time, mdblack98@... writes: 
Look in services for "WAV" audio items.  Disable them.  I believe  there are two of them.Mike       On Tuesday, October 4, 2022 at 04:25:22 PM CDT, Stan Galonski via groups.io <sgalonski1@...> wrote:   All, My old setup was a Windows 10 desktop, Signalink usb, Yaesu FTDX5000 and running HRD as the logging program all worked well with 1,000's of QSOs logged. I upgraded my Desktop to a Dell Inspiration 3900 running Windows 11, I can't get WSJT to work, no stations show in Band activity or the Graph, Tune will show 100 watts then drop to 35 watts after 5 seconds. I can Log a dummy QSO and it will show on the HDR log.  I have set up WSJT and HRD per their manual, HDR seems fine unless I start WSJT first then I get a "com 3 in use by another program".  I am at a total loss on what to do next. 73, StanKK3KK


Dennis W1UE
 

Did the driver install correctly for the Signallink? Can you see it in
Device Manager?

UE

On Tue, Oct 4, 2022 at 7:12 PM Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

1. Wrong sound card selected - using Signalink USB - how would I select
it?
2. Wrong sound card input selected - set to both set to usb audio codex
3. Input to the sound card not adjusted correctly. - how is this set?
4. If you have a USB sound card available, try using i- using Signlink USB
5. Does your computer have separate jacks for headphones and microphone?
- Yes

Like I stated the exact setup was working on my old windows 10
system StanKK3KK
In a message dated 10/4/2022 3:21:41 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan
Do any signals show in the waterfall? If not,
Then either
1. Wrong sound card selected
2. Wrong sound card input selected
3. Input to the sound card not adjusted correctly.
4. If you have a USB sound card available, try using it
5. Does your computer have separate jacks for headphones and microphone?

Dennis W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
That's the issue, trying to get it to work with just the rig. Followed
the setup procedure and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first. If wsjt doesn’t work,
then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10 desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no
stations
show in Band activity or the> Graph, Tune will show 100 watts then drop
to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on the
HDR log. I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".> I am at a total loss on what to do next.> 73, StanKK3KK>>>















Stan Galonski
 

I have 12 devices under "Universal Serial Bus Controllers", can't tell which one is for the signalink, have gone through each one and updated the driver

In a message dated 10/4/2022 5:09:52 PM Pacific Standard Time, egan.dennis88@... writes: 
Did the driver install correctly for the Signallink?  Can you see it in
Device Manager?

UE

On Tue, Oct 4, 2022 at 7:12 PM Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

  1. Wrong sound card selected  -  using Signalink USB - how would I select
it?
2. Wrong sound card input selected -  set to both set to usb audio codex
3. Input to the sound card not adjusted correctly. -  how is this set?
4. If you have a USB sound card available, try using i-  using Signlink USB
5. Does your computer have separate jacks for headphones and microphone?
-  Yes

  Like I stated the exact setup was working on my old windows 10
system StanKK3KK
In a message dated 10/4/2022 3:21:41 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan
Do any signals show in the waterfall?  If not,
Then either
1. Wrong sound card selected
2. Wrong sound card input selected
3. Input to the sound card not adjusted correctly.
4. If you have a USB sound card available, try using it
5. Does your computer have separate jacks for headphones and microphone?

Dennis W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
  That's the issue, trying to get it to work with just the rig. Followed
the setup procedure  and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first.  If wsjt doesn’t work,
then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10 desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no
stations
show in Band activity or the> Graph, Tune will show 100 watts then drop
to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on the
HDR log.  I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".>  I am at a total loss on what to do next.>  73, StanKK3KK>>>















Reino Talarmo
 

I have 12 devices under "Universal Serial Bus Controllers", can't tell which one is for the signalink, have gone through each one and updated the driver
Hi,
You may disconnect USB cable to see what changes. Or power up Signalink without Signalink USB cable connected and then connect the USB cable to see changes. Also Signalink power down will do.
73, Reino OH3mA


Dennis W1UE
 

Stan

This is the point where I throw up my hands., have a good sleep, get up
early and get
that first cup of coffee. I'll then disconnect everything, delete as many
drivers as I can,
get out the manuals, and redo the entire installation. Don't do it from
memory; start with
the Signallink manual, follow the install instructions step by step. Do a
few simple tests
to make sure it works. Then go on to WSJT. Install it, configure it, and
make sure it
works. THen add in HRD.

My suspicion is that a step was missed, or didn't install correctly. By
starting anew and
following the installation instructions step by step, you should find that
missing link.

Dennis W1UE


On Tue, Oct 4, 2022 at 9:17 PM Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

I have 12 devices under "Universal Serial Bus Controllers", can't tell
which one is for the signalink, have gone through each one and updated the
driver

In a message dated 10/4/2022 5:09:52 PM Pacific Standard Time,
egan.dennis88@... writes:
Did the driver install correctly for the Signallink? Can you see it in
Device Manager?

UE

On Tue, Oct 4, 2022 at 7:12 PM Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

1. Wrong sound card selected - using Signalink USB - how would I
select
it?
2. Wrong sound card input selected - set to both set to usb audio codex
3. Input to the sound card not adjusted correctly. - how is this set?
4. If you have a USB sound card available, try using i- using Signlink
USB
5. Does your computer have separate jacks for headphones and microphone?
- Yes

Like I stated the exact setup was working on my old windows 10
system StanKK3KK
In a message dated 10/4/2022 3:21:41 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan
Do any signals show in the waterfall? If not,
Then either
1. Wrong sound card selected
2. Wrong sound card input selected
3. Input to the sound card not adjusted correctly.
4. If you have a USB sound card available, try using it
5. Does your computer have separate jacks for headphones and microphone?

Dennis W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
That's the issue, trying to get it to work with just the rig. Followed
the setup procedure and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first. If wsjt doesn’t work,
then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10
desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program
all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a
Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no
stations
show in Band activity or the> Graph, Tune will show 100 watts then drop
to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on
the
HDR log. I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".> I am at a total loss on what to do next.> 73, StanKK3KK>>>

























Bruce N7XGR
 

Stan, That device will not show up in the USB controllers tree.
Expand the Audio tree to find a USB Audio CODEC device if
the driver installed correctly.
Open the Sound Settings by right clicking on the Speaker in the
system tray, do you find the USB Audio CODEC for both the audio
in and out?
Did you go into the security settings to allow the Signalink received
audio through. This link works for Win 11 also,
https://support.microsoft.com/en-us/windows/turn-on-app-permissions-for-your-microphone-in-windows-10-94991183-f69d-b4cf-4679-c98ca45f577a
Make sure that the default audio device in the Sound properties
is the one in the PC, not the Signalink unit, if the PC audio
card has a Green check mark for both the audio in and out
then it is the default device, check both tabs for this.
Do all testing into a dummy load.

Bruce N7XGR







Mike Koralewski K8VA
 

On Tue, Oct 4, 2022 at 09:17 PM, Stan Galonski wrote:


I have 12 devices under "Universal Serial Bus Controllers", can't tell which
one is for the signalink, have gone through each one and updated the driver

In a message dated 10/4/2022 5:09:52 PM Pacific Standard Time,
egan.dennis88@... writes: 
Did the driver install correctly for the Signallink?  Can you see it in
Device Manager?

UE

On Tue, Oct 4, 2022 at 7:12 PM Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

  1. Wrong sound card selected  -  using Signalink USB - how would I
select
it?
2. Wrong sound card input selected -  set to both set to usb audio codex
3. Input to the sound card not adjusted correctly. -  how is this set?
4. If you have a USB sound card available, try using i-  using Signlink USB
5. Does your computer have separate jacks for headphones and microphone?
-  Yes

  Like I stated the exact setup was working on my old windows 10
system StanKK3KK
In a message dated 10/4/2022 3:21:41 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan
Do any signals show in the waterfall?  If not,
Then either
1. Wrong sound card selected
2. Wrong sound card input selected
3. Input to the sound card not adjusted correctly.
4. If you have a USB sound card available, try using it
5. Does your computer have separate jacks for headphones and microphone?

Dennis W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
  That's the issue, trying to get it to work with just the rig. Followed
the setup procedure  and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first.  If wsjt doesn’t work,
then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10 desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no
stations
show in Band activity or the> Graph, Tune will show 100 watts then drop
to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on the
HDR log.  I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".>  I am at a total loss on what to do next.>  73, StanKK3KK>>>

You are on the right track, just a different train. I too had difficulty making Wsjt-x operate with Windows 11..It seems that just about every USB Bus controller as well as the Drivers in Windows have a power management setting... Usually on the last tab of the configuration dialog box
Setting ALL the power management to Off.. Solved the problem.
73 Mike K8VA



















--
73 Mike 73


Stan Galonski
 

Mike,
 Turned off Power management on all USB items  -- no help still have the same problem. StanKK3KK

In a message dated 10/5/2022 6:55:10 AM Pacific Standard Time, k8va@... writes: 
On Tue, Oct  4, 2022 at 09:17 PM, Stan Galonski wrote:


I have 12 devices under "Universal Serial Bus Controllers", can't tell which
one is for the signalink, have gone through each one and updated the driver

In a message dated 10/4/2022 5:09:52 PM Pacific Standard Time,
egan.dennis88@... writes: 
Did the driver install correctly for the Signallink?  Can you see it in
Device Manager?

UE

On Tue, Oct 4, 2022 at 7:12 PM Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

  1. Wrong sound card selected  -  using Signalink USB - how would I
select
it?
2. Wrong sound card input selected -  set to both set to usb audio codex
3. Input to the sound card not adjusted correctly. -  how is this set?
4. If you have a USB sound card available, try using i-  using Signlink USB
5. Does your computer have separate jacks for headphones and microphone?
-  Yes

  Like I stated the exact setup was working on my old windows 10
system StanKK3KK
In a message dated 10/4/2022 3:21:41 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan
Do any signals show in the waterfall?  If not,
Then either
1. Wrong sound card selected
2. Wrong sound card input selected
3. Input to the sound card not adjusted correctly.
4. If you have a USB sound card available, try using it
5. Does your computer have separate jacks for headphones and microphone?

Dennis W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
  That's the issue, trying to get it to work with just the rig. Followed
the setup procedure  and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first.  If wsjt doesn’t work,
then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10 desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no
stations
show in Band activity or the> Graph, Tune will show 100 watts then drop
to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on the
HDR log.  I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".>  I am at a total loss on what to do next.>  73, StanKK3KK>>>

You are on the right track, just a different train. I too had difficulty making Wsjt-x operate with Windows 11..It seems that just about every USB Bus controller as well as the Drivers in Windows have a power management setting... Usually on the last tab of the configuration dialog box
Setting ALL the power management to Off.. Solved the problem.
73 Mike K8VA



















--
73 Mike 73


Stan Galonski
 

Bruce,
 Both Codecs are there, default and permissions set correctly. Still not working. Thanks for the suggestions. StanKK3KK

In a message dated 10/5/2022 4:21:27 AM Pacific Standard Time, n7xgr1@... writes: 
Stan,  That device will not show up in the USB controllers tree.
Expand the Audio tree to find a USB Audio CODEC device if
the driver installed correctly.
Open the Sound Settings by right clicking on the Speaker in the
system tray, do you find the USB Audio CODEC for both the audio
in and out?
Did you go into the security settings to allow the Signalink received
audio through.  This link works for Win 11 also,
https://support.microsoft.com/en-us/windows/turn-on-app-permissions-for-your-microphone-in-windows-10-94991183-f69d-b4cf-4679-c98ca45f577a
Make sure that the default audio device in the Sound properties
is the one in the PC, not the Signalink unit, if the PC audio
card has a Green check mark for both the audio in and out
then it is the default device, check both tabs for this.
Do all testing into a dummy load.

Bruce  N7XGR







Stan Galonski
 

Dennis,
 That's my plan, I'm going to start with cabling and set up each one. I know that the rig interface works because I can run HRD - see and control the rig and log, so that's the last step.  It has to be something simple that I missed, lots of Ham running my same setup without issues on a Windows 11 system. Thanks for you help and suggestions, I'll post when I get it working. StanKK3KK

In a message dated 10/5/2022 2:56:47 AM Pacific Standard Time, egan.dennis88@... writes: 
Stan

This is the point where I throw up my hands., have a good sleep, get up
early and get
that first cup of coffee.  I'll then disconnect everything, delete as many
drivers as I can,
get out the manuals, and redo the entire installation.  Don't do it from
memory; start with
the Signallink manual, follow the install instructions step by step.  Do a
few simple tests
to make sure it works.  Then go on to WSJT.  Install it, configure it, and
make sure it
works.  THen add in HRD.

My suspicion is that a step was missed, or didn't install correctly.  By
starting anew and
following the installation instructions step by step, you should find that
missing link.

Dennis W1UE


On Tue, Oct 4, 2022 at 9:17 PM Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

I have 12 devices under "Universal Serial Bus Controllers", can't tell
which one is for the signalink, have gone through each one and updated the
driver

In a message dated 10/4/2022 5:09:52 PM Pacific Standard Time,
egan.dennis88@... writes:
Did the driver install correctly for the Signallink?  Can you see it in
Device Manager?

UE

On Tue, Oct 4, 2022 at 7:12 PM Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

  1. Wrong sound card selected  -  using Signalink USB - how would I
select
it?
2. Wrong sound card input selected -  set to both set to usb audio codex
3. Input to the sound card not adjusted correctly. -  how is this set?
4. If you have a USB sound card available, try using i-  using Signlink
USB
5. Does your computer have separate jacks for headphones and microphone?
-  Yes

  Like I stated the exact setup was working on my old windows 10
system StanKK3KK
In a message dated 10/4/2022 3:21:41 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan
Do any signals show in the waterfall?  If not,
Then either
1. Wrong sound card selected
2. Wrong sound card input selected
3. Input to the sound card not adjusted correctly.
4. If you have a USB sound card available, try using it
5. Does your computer have separate jacks for headphones and microphone?

Dennis W1UE

On Tue, Oct 4, 2022 at 18:08 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote:

Dennis,
  That's the issue, trying to get it to work with just the rig. Followed
the setup procedure  and no signal decodes? StanKK3KK
In a message dated 10/4/2022 2:52:38 PM Pacific Standard Time,
egan.dennis88@... writes:
Stan My best advice- get wsjt-x to work first.  If wsjt doesn’t work,
then
thetwo programs won’t work. Once that works, add in HRD. Dennis W1UE On
Tue, Oct 4, 2022 at 17:25 Stan Galonski via groups.io <sgalonski1=
aol.com@groups.io> wrote: > All, My old setup was a Windows 10
desktop,
Signalink usb, Yaesu FTDX5000> and running HRD as the logging program
all
worked well with 1,000's of QSOs> logged. I upgraded my Desktop to a
Dell
Inspiration 3900 running Windows> 11, I can't get WSJT to work, no
stations
show in Band activity or the> Graph, Tune will show 100 watts then drop
to
35 watts after 5 seconds. I> can Log a dummy QSO and it will show on
the
HDR log.  I have set up WSJT> and HRD per their manual, HDR seems fine
unless I start WSJT first then I> get a "com 3 in use by another
program".>  I am at a total loss on what to do next.>  73, StanKK3KK>>>

























Peg Daly N3PEG
 

Might not be related to this particular problem, but I found out that a lot of knock-off Prolific chips were used to make various ham radio interface cables. Prolific recently rewrote their drivers to no longer recognize these knock-off chips. I found that out when my interface to my IC-7000 no longer worked after my laptop updated from Win10 to Win11 earlier this year. I ended up buying a new cable with the FTDI chip and it solved the problem. The other solution is to find the older Prolific driver and install it. It's hard to find. Now, all my newer cables have the FTDI chip, but I can still use that older cable with my old Win10 desktop.


Stan Galonski
 

Thanks, I have a new one on order with the FTDI Chip and upgrading my old USB Hub just in case. The new Desktop has fewer USB ports then my old one.
  73,  StanKK3KK

In a message dated 10/6/2022 1:37:36 PM Pacific Standard Time, PegDalyPA@... writes: 
Might not be related to this particular problem, but I found out that a lot of knock-off Prolific chips were used to make various ham radio interface cables.  Prolific recently rewrote their drivers to no longer recognize these knock-off chips.  I found that out when my interface to my IC-7000 no longer worked after my laptop updated from Win10 to Win11 earlier this year.  I ended up buying a new cable with the FTDI chip and it solved the problem.  The other solution is to find the older Prolific driver and install it.  It's hard to find.  Now, all my newer cables have the FTDI chip, but I can still use that older cable with my old Win10 desktop.