These boxes control the freq range of the waterfall, I suspect you have managed to change them [cid:image001.png@...] Peter M0PWX M0PWX Grabber Page (qsl.net)<https://www.qsl.net/m0pwx/g

#TechnicalHelpQuestion

The other one is if you have a HDMI external monitor, turn off sleep / screen saver for it, solved my issues a year or so back, as my radios are running wspr / QRSS / and various other protocols overn

#stopped_working

I tend to migrate to FT4 when FT* is busy, as its tends to be quieter and so you can be heard easier and often get better DX 😊 Peter M0PWX M0PWX Grabber Page (qsl.net)<https://www.qsl.net/m0pwx/grabbe

#general

the 2 things that control the wide graph are the "bins/pixel" and the "start xxxhz" but these are only visible if you have the "controls" box ticked my settings below (pls excuse dodgy drawing to high

#frequency

So I have found this page re CE19 interface and G90 XIEGU-Radio-Data-Communication-Connection-Setup-Tutorial.pdf<https://xiegu.eu/wp-content/uploads/sites/4/2020/06/XIEGU-Radio-Data-Communication-Conn

#linux #WSJTX_config

Look at page 7 of this doc Cheat Sheet V1.77 070421.pdf (groups.io)<https://xiegug90.groups.io/g/main/files/Manuals,%20Cheat%20Sheets,%20CAT-CIV%20Commands%20and%20other%20Information./Cheat%20Sheet%2

#linux #WSJTX_config

Picture paints a thousand words Below is my G90 on TX [cid:image001.png@...] You can use the blue USB to serial cable programming cable for CAT control, just make sure you have the corre

#linux #WSJTX_config

I always use WSJT-x, if you look at the info on bottom left of pskreporter it often shows the application being used [cid:image001.png@...] Peter M0PWX M0PWX Grabber Page (qsl.net)<https

#MSK144

Use PSK reporter and set it to look for anyone using MSK144 in the last couple of hours, their won’t be many, see preconfigured link below Display Reception Reports (pskreporter.info)<https://www.pskr

#MSK144

My 991a produces max output as the bar goes into red. i.e. if I set 30w on front output is 30w at the end of the white section of the ALC bar graph with the ALC at virtually 0 i get 1-2w out here when

#decode

Check the ALC and power out bars when you TX, is your radio getting enough audio so you are getting the correct power out? I normally have my DT gain set so the ALC bar just goes into the red or my ri

#decode

FT8 has a 15 second cycle, FT4 has a 7.5 second cycle, and depending on if you use RR73 or RRR as the 4th message it is 5 or 6 messages for a QSO For speed FT4 is the mode of choice with 6 messages it

#FT8

All of the WSJT-x modes use SSB as it is just a single carrier that changes a in a 50hz block for signal, so many signals can be present in a 3khz channel without massive interference FM would never w

#FT8

Hi Marty PSKReporter has suffered a database failure I believe It is being worked on, and the site owner is doing his best to get it back online ASAP 73 Peter M0PWX M0PWX Grabber Page (qsl.net)<https:

#FT8

Not sure about 2.5.2, but there were issues with some versions in the past. The issues I saw were about having he tune box ticked in the schedule, if you don’t need to tx a small “tuning” signal for a

#WSPR

I tend to go to FT4 quite often, as it is less popular so you can actually work less common stations as there is space in the spectrum both side I also like JTAlert, Activity window is great to see th

#FT4 #QSO_practices

Sad news indeed, Bill was a great resource and font of so much knowledge, as well as having the patience of a saint when dealing with some members / questions Will be greatly missed on here Peter M0PW

#general

My results from a bit closer 025845 -3 12.8 1507 & G4JNT TESTING 033900 -6 14.7 1502 & G4JNT TESTING 044415 -2 1.4 1514 & G4JNT TESTING 050500 -1 4.9 1483 & G4JNT TESTING 050515 -3 0.4 1488 & G4JNT TE

#MSK144

Andy I got a few spot for you overnight 234415 -8 2.7 1495 & G4JNT TESTING 030515 -4 2.2 1498 & G4JNT TESTING 030515 -1 2.6 1497 & G4JNT TESTING 050400 -5 1.6 1480 & G4JNT TESTING 054500 -2 2.8 1479 &

#Beacons

Listening down here in kent Peter M0PWX M0PWX Grabber Page (qsl.net) MSK144 Beacon for the Leonids later this evening. Latest operational state can be found here. http://g4jnt.com/MSK144_Beacon.txt

#Beacons