Just load your grid square during initial setup of WSJT. The software then automatically inserts it into Exchange #1 which is CQ YOURCALL grid. This is detailed in the general setup instructions, or t

#FT4 #FT8

GARETH - It appears that you are working with an old version - the current version of WSJTx is 2.5.4 and it is already a few months old.

#raspberryPi #WSPR

TIM D - forget anything to do with Signalink. His FT991 has dual USB links over a single cable, one is digital just for CAT and the second is analog just for audio. Mike S VE3UET - I don't have an FT9

#NewUser

Oh silly me. Through my 57 years in ham radio so far, I thought the huge variety of contests were intended to compare amateur licensees' operating abilities in varied environments. It never once dawne

#EnhancementReqest

To each his own, but it's probably better to download the current version periodically, then follow the widely recommended practice of installing each new version update into a separate subfolder name

#windows11

Please do yourself and others running the FT4 and FT8 modes a favor by using only time syncing programs that use the full NTP protocol. Meinberg is full true NTP, no compromises. SNTP, (aka Simple NTP

#Timesync

To make your experiment more valid and repeatable, you should be using two identical receiver-decoder devices fed by separate antenna systems. That removes the obvious RF and audio phase differences o

#AudioIssues

The fallacy in your example is that WSJTx has no such audio "slot" boundaries, so operator 2 on 1275 cannot be "taking up 2 slots." The audio signal occupies a window from the listed audio frequency t

#FT8

Any chance that you activated the option for "Morse ID after contact complete"?? That can do it, even if you did not define the DTR and RTS leads of your CAT control port.

#Yaesu

WSJTx does not work with a CW transmitter or receiver. It also does not work over FM on VHF bands It generates normal upper sideband on both transmit and receive, on all WSJT preferred frequencies. Th

#WSPR

One further caution: Do NOT set the soundcard interface port to be either the "Default" or "Communications Default" device! As Ron hinted above, your "Default" device should be the PC soundcard for sp

#AudioIssues

First, please DO NOT invent your own arbitrary response message. The effect is like inventing your own Q signals on CW - nobody else's copy of WSJT will know what it means. The predefined response tex

#NewUser

Microsoft did the same thing to Windows 10 users a few months back. It's generally not a good idea for Apple to mimic them so closely! Karl Beckman

#macOS

STEFAN - The "No Audio from Rear Panel" condition exists when you inject PTT via either CAT command or serial RTS logic low to the Mic PTT line. Either signal mutes the TS2000 rear panel audio input;

#IssueReport #Kenwood #linux #Cat_RigControl #txaudio

Self-proclaimed NON-power user here: I was having similar "crash" issues with WSJTx when I updated to the 2.5.3 64 bit version on Windows 10. Two weeks ago I installed the 32 bit version of 2.5.3 whic

#wsjt-x-crashing

CLUE:The 32 version was your pre-retirement original and you say that worked fine. I had problems similar to those you described when I installed the 2.5.3 64-bit download, updating from 2.5.2 64-bit

#Cat_RigControl #Windows10

Goiod Morning, Dick - Is there any chance that you have set up your JTAlert installation to auto-open WSJTx? Since WSJTx starts OK and works fine on its own, it looks like JTAlert is causing the start

#windows11

Stefan: The Kenwood TS-2000 is indeed a bit peculiar regarding use of the rear panel 13-pin DIN J7 accessory connector for data interfaces. If you are sending USB sound card audio to the rear connecto

#linux #Cat_RigControl #txaudio #IssueReport #Kenwood

@Mchael Black S T O P - S A F E T Y I S S U E !! When you get out that multimeter to evaluate the ground potential difference: FIRST use the ACV scale to measure between the copper flashing to outlet

#Cat_RigControl #AudioIssues

#Steve (M0NMA) and G8IOA WSPR requires the station operator to input the grid locator detail that is to be transmitted, Assuming the software is operating correctly, it can neither insert an arbitrary

#IssueReport #WSPR