Hi Dave, OK, so your PTT is being controlled by the SignaLink USB using its internal digital audio VOX circuit. That means there are two possibilities for the issue of the PTT hanging you are reportin

#txaudio #Alinco

Hi Dave, throughout this discussion I cannot find any reference by you about if you have a CAT connection to your rig. Is the only connection you have via the SignaLink USB interface? 73 Bill G4WJS.

#txaudio #Alinco

Hi Bill, before doing that ensure that WSJT-X has access to microphone devices in the Windows Camera and Microphone Security settings. Often the simple solution is all that is needed. 73 Bill G4WJS.

#AudioIssues #Elecraft #Windows10

Hi Terry, the message source encoding for the 77-bit modes like FT8 is fully described here: https://physics.princeton.edu/pulsar/K1JT/FT4_FT8_QEX.pdf I don't see what's wrong with setting up some fre

#EnhancementReqest

Hi Bruce, thanks for that correction. The IC-7200 user manual says nothing at all about a VCP for CAT control over the USB connection, only audio connections are mentioned, not helpful by Icom. 73 Bil

#Icom #Cat_RigControl

Hi Jim, have you set your IARU Region in "Settings->General"? Have you tried resetting the "Settings->Frequencies->Working Frequencies" table? 73 Bill G4WJS.

#FT4

Hi Jim, can you try WSJT-X v2.5.0 RC6 and report back how that goes please? 73 Bill G4WJS.

#FT4

Hi Rob, as far as I can see, the IC-7200 does not provide a CAT virtual serial port via its USB connection. I suspect you need a separate CI-V interface to connect it to your PC for CAT control. In th

#Icom #Cat_RigControl

Hi Mike, have you installed the 64-bit version of WSJT-X? Have you checked if the required Microsoft Visual C++ redistributable is installed? Details in the WSJT-X User Guide: https://physics.princeto

#Windows10

Hi Stan, the "Settings->Radio->Transmit Audio Source" is only relevant for a small number of rigs where there are two CAT Tx commands and the audio source depends on which is used to key the rig. You

#install #WSJTX_config #raspberryPi #Icom

Hi Tim, do you have "CI-V Transceive Mode" enabled on your IC-7300? It should be disabled. 73 Bill G4WJS.

#Cat_RigControl

Hi Mike, sure that needs fixing, but I can workaround much more simply by using USB as the mode. I don't think I am able to replicate the OP's issue with my setup with no rig, so I am bowing out here

#wsjt-x-crashing

Hi Mike, I take that back, perhaps I can help here. I tried using "Settings->Radio->Mode->Data/Pkt" in WSJT-X and got this crash in the Hamlib flrig back end: Thread 15 "QThread" received signal SIGSE

#wsjt-x-crashing

Bob, sorry, I have no idea what this message is about. Please re-read he instructions I gave to get a trace log file below, you appear to have ignored them. particularly the part about sending the log

#Cat_RigControl

Hi Mike, thanks, that allows me to run with the flrig from the Raspberry Pi OS repos. Unfortunately I don't think is going to help much with no rig attached. Strange things happen like SPLIT Tx freque

#wsjt-x-crashing

Mike, Hamlib is of no relevance here, at least not for the original issue I am trying to investigate. N1MM Logger+ emulates the DX Lab Suite Commander rig control server. 73 Bill G4WJS.

#Cat_RigControl

Hi Bob, that would appear to be an issue with N1MM Logger+. So I can be sure please put the attached file into the log files directory of the WSJT-X instance that is using N1MM Logger+ for rig control

#Cat_RigControl

Hi Bob, OK, so if you change that to Mode->None does the issue you initially reported go away? 73 Bill G4WJS.

#Cat_RigControl

Bob, I asked about the "Settings->Radio->Mode" option. You stated you set the rig mode manually. I asked if you had the "Settings->Radio->Mode->None" option checked. I asked that because with that con

#Cat_RigControl

Hi Rob, go to "Settings->Frequencies", then *right-click* the body of the Working Frequencies table, and press the Reset button. 73 Bill G4WJS.

#WSPR #FST4W