DAVE - Previous postings to initiate this thread were made in November 2018, and reflect the current WSJT-X version at that time. It helps to read back to the beginning of the thread before resurrecti

#WSJTX_config

Export only ft8 ft4 contacts and whatever other wsjt modes to an adi file and rename it and set it in the wsjt folder. Also rescanning your lig using jtalert will also give you worked b4 etc.

#WSJTX_config

Hi Reino and All; After testing: ADIF MASTER WORKS FB FOR EDITING AND LOG MERGING ! Just done: With ADIF Master opened initial HOME log wsjtx_log.adi that contained by error logged several portable QS

#WSJTX_config

Hi Bill, Thanks for the response. My problem is not only the merging, but how to extract two QSO date blocks and to create two .adi logs, one containing QSOs from my Home locator JN08WT and another fo

#WSJTX_config

Hi Carl, Thanks for the response. You said ADIF Master is not needed. But then which application to use to open the wsjt_log.adi , cut QSOs from certain date blocks and create two new .adi files, one

#WSJTX_config

check under frequencies tab, station info. do yoiu have any antennas listed there?? not sure if that is where PSK reporter gets it from Dave Garber VE3WEJ / VE3IE

#WSJTX_config

I am having a problem in that I cannot share the Memory when I try to access the Software.

#WSJTX_config

STEP 1: Get on the proper legal frequency! 5358.5 kHz is the center of the authorized channel. Carrier (dial) frequency when using upper sideband mode is 5357.0 kHz. STEP 2: The WSJT instructions are

#WSJTX_config #FT8

Hi Roy, Thanks for responding. Is this a suggestion in order to "clean up" and reduce the miscellaneious signals? Or some other reason? Thx, Jeff

#WSJTX_config

HI Alan, Thanks for responding. I did some testing with an attenuator in line, but no luck yet. Have to do some more testing with it and some other's suggestions as well. Thx, Jeff

#WSJTX_config

>I had the transmit frequency incorrect in the Arduino firmware that controls the 5351...I have since corrected to transmit on 14.0956 MHz and there is now a steady signal at that frequency, which I b

#WSJTX_config

Thanks for the reply, Bill. I was able to rectify "most" of the issues, but one still has me stymied: no audio! I set the interface up as directed by the manufacturer, but there is no audio. I can hea

#install #WSJTX_config

Hey Don... I too have been using using the Rigblaster with audio problems.. I got a Signalink USB and plan to use that with my TS-2K.. would you send me a few screen shots of the options you use for W

#bluetooth #AudioIssues #WSJTX_config

Reino thank you so much. I discovered that my logging program Log4OM placed a header in the adi file when I created it. I edited that out and all my QSOs load properly. I never would have figured that

#WSJTX_config

Guys I am having the same problem Tom had. I open log directory>I drop my QSO adi file into the wsjtx_log.adi and all my qsos show up. I save it. I close the program and no qsos are there when I start

#WSJTX_config

Hi Erwin, for one QSO you can enter the DX callsign and grid if known into the WSJT-X main window with the correct mode selected, then press the "Log QSO" button. The QSO start and end times can be ad

#WSJTX_config

I know WSJTX has a setting to adjust the delay between issuing the transmit command and generating the audio tones. Has any consideration been given for implementing a complimenting setting to allow a

#WSJTX_config

anyone know whats going on with wspr? ....no decode anymore? Sent from my Verizon, Samsung Galaxy smartphone

#mac #WSJTX_config

Thanks for the help again, Bill. I tried the instructions on the link you posted, and I also found some older versions of WSJT-X still lurking in a Windows backwater... However, the cache clear did no

#WSJTX_config

>My comments about the RIT/XIT/CLARIFIER - those can move the signals to the point that they start clipping as they hit the I.F. filters & that generates the distortion. (Just as they change the pitch

#WSJTX_config