My stn is showing on 40 but not the antenna I have set in the freq. tab It's just showing my location and LOTW sign on psk reporter. Any thoughts wud be appreciated.

#GeneralGroupInfo

I have. And it frequently locks up (spinning beachball) when I try. What has worked is the following sequence: 1. quit WSJT-X 2. change radios in logging software (MacLoggerDX) 3. launch WSJT-X 4. cha

#GeneralGroupInfo

Do you mean by input DC power to your final amplifier or RF input to an external power amplifier? Well, that recommendation is two-folded, with a typical 100 W rig 30-35 W is (really) safe output powe

#GeneralGroupInfo

By the way have you tried Configurations? Those should work without any need for quitting or restarting. 73, Reino OH3mA Lähettäjä: main@WSJTX.groups.io [mailto:main@WSJTX.groups.io] Puolesta Chip via

#GeneralGroupInfo

I tried PSK reporter this morning and the counter is not showing reports. I am on 40 FT8 and the antenna shows on reporter a 30/60 OFCD. I have my antenna for Hustler vertical/40-80 vee. I even e-mail

#GeneralGroupInfo

Since around 1970, FCC Rules have been for output. WSJT-X modes are WEAK SIGNAL modes, not necessarily low power modes. On the HF bands, yes, most of us run 25-40W. It's also good to run no more than

#GeneralGroupInfo

We are advised to use around 30-35 watts on FT8. Input or output? 73 Roger/K0kon

#GeneralGroupInfo

I believe that you must add the antenna station information by each band - settings.... - frequencies then enter station information

#GeneralGroupInfo

There is an explanation about color highlighting in wsjtx in the MANUAL SECTION 4.7 that will help with some of the issues of worked B-4 status. It seems to work for many but READ THE MANUAL :) This c

#FT8 #GeneralGroupInfo

I thought I knew my way around the Mac pretty well, but that’s a new one on me. I was able to successfully make that work. Seems to work pretty well. It’s still a little quirky to switch between radio

#GeneralGroupInfo

did he send a florida grid, or is that just where he gets his mail for qsling... I see that alot for cuba as well Dave Garber VE3WEJ / VE3IE

#GeneralGroupInfo

For the Mac, you can use the Audio Midi Setup App (usually in the Utilities folder in Applications) to create new Aggregate devices (like IC9700 in and IC9700 out and IC7300 in and IC7300 out which us

#GeneralGroupInfo

Bill I just checked 30 meters and 30 gave reports but still had my antenna as a Hustler vertical not my 30/60 OCFD. I dont know what is going on???

#GeneralGroupInfo

Thanks Bill I just posted on the PSK REPORTER THIS PROBLEM. I made a couple of FT8 qsos this am. Not only did it report any stations I heard or 40 nor any antenna info at all.

#GeneralGroupInfo

Hi Dave, if you do not have that station information the WSJT-X "Settings->Frequency-Station Information" table for any band then I don't see how WSJT-X could possibly invent the information you are s

#GeneralGroupInfo

Longtime WSJT/WSPR/Digimode operator here....not saying I'm an "expert" though! This is what works for me (Yaesu, Kenwood and Icom) and has resulted in a clean signal on FT8, WSPR, JT9, FT4, Q65, etc

#GeneralGroupInfo #FT8

There is. Go to control panel\sound and you will see a Codec under the recording tab and one under the playback tab, select properties for each one and rename as you choose. See attached for example.

#GeneralGroupInfo

When I monitor 30 meters it shows my antenna as a Hustler vertical and 5 band beam. I don't these antennas in my freq tab. I have for 30 & 60 as a OCFD. Any thoughts ? Thanks 73's de NU4N/Dave

#GeneralGroupInfo

Hi Ken, May I repeat that most of that problem is easily prevented by using Split either “Rig” or “Fake it”, if cat control is available. As explained in the User Guide during transmission audio frequ

#GeneralGroupInfo #FT8

Which can be a problem. For example I worked Puerto Rican station today who's QRZ page listed an address and grid in Florida. My logging program not only wanted to populate with the wrong grid but wit

#GeneralGroupInfo