For those, who like me, have had issues with Windows 'messing' with the USB/audio there is a very interesting article that explains whats going on. Its called USB soundcards and is in the Data section

#FT4 #FT8 #txaudio

30M is fairly limited, it seems, because not a lot of people have antennas for the band. Much like 60M. Of course the ones that do, seem to stick to FT8. 73 - John - N7GHZ

#FT4

Hi, You could send "W0XXX QRA PSE" hi! 'Kari, oh2gqc

#FT4 #QSO_practices #FT8

OK Jim I am using 160m FT8 almost every morning. On Oct 28, 2020, had the first and only one 160m QSO with the USA with a new antenna. I hope for many more. Starting tomorrow morning , I will be activ

#FT4

Ror NA, 160 just starts to open at 2200z. Could you please run later? I thank you in advance. Bruce, W8HW in Florida, USA

#FT4

Hi everybody! It did work in a modest way. As you can see in the screen snip, one 160n FST4 QSO was made with PA9CC. Please note that I did receive PA9CC at -29 dB. Let's continue tomorrow evening, sa

#FT4

Larry and All In addition: 1. I will call CQ on 19:00, 19:30, 20:00, 20:30, 21:00, 21:00, 21:30 UTC for 15 minutes each time. 2. What shell I do with NB? Join me Amos 4X4MF Larry Starting now, this ev

#FT4

Amos, Most of what little activity I have seen occurs between about 800 to 1200 so I set Flow at 500 and Fhi at 1300. Start with the NB set to 0, but gradually increase it as you gain experience. You

#FT4

Hi Amos, where possible we will not recommend frequencies or modes, it's just too difficult to satisfy all parties. I suggest you coordinate with other users and find slots and modes that work for you

#FT4

I am listening now on 1839.000 Khz FST4 Please join me with WSJT-X v2.3.0 rc2 Amos 4X4MF

#FT4

I’ve been following this thread because, although I get a decent amount of QSOs, including EU, CA, and US, my signal reports are always around -20 dB. My rig is a Yaesu FTDX 3000 using CAT control wit

#FT8 #FT4

I check and CQ on 30M FT4 almost daily. I have managed some contacts (30) but they are few and far between. Mike WB9QVY

#FT4

According to the WSJT-X documentation, contest-mode using a compound callsign is not supported in FT4/FT8, but I found a workaround, which may be of interest. This applies to calls like S5/PA3BHF, but

#FT8 #FT4

There are interesting discussions on what constitutes a valid FT4/8 QSO and what doesn't. Your logger logs a QSO when you send 73 (or when you force it to log), but that does not mean the receiver act

#FT4

Hi Bill. Tnx fer reply and sri for delay. The PTT is USB via Serial converter and RTS. Its worked fine for years. Anyway, I went back and had a run with MixW and BPSK. All worked as usual so it wasn’t

#FT4

Very neat! Thanks. Dave G0WBX.

#FT8 #FT4

It is very common on both FT4 and FT8. I have some callers start with a signal report and no initial call. It still works and they end up in the log. 73, N0AN Hasan

#QSO_practices #FT4

Hi Pete, they work for me, although the steps are 90 Hz for the wide FT4 mode. 73 Bill G4WJS. Hi Bill and Pete, I have same problem in Windows 7, but works in Windows 10. In Windows 7 Shift-F11 jumps

#FT4

Um ... you're not just on 4 frequencies, you'll have signals all over the bandwidth. What they are saying is that you should NOT just use simplex to answer someone, but work 'split' (which is not the

#FT4

Thank you!

#FT4