I can not understand what this problem really is because all three USB-D filters can be adjusted to user preference. Page 73 of the IC9100 user manual describes on how to adjust the filter widths. In

#Cat_RigControl #Icom

Thanks for that tip Bill, works like a charm. 73, Bernd - KB7AK

#Cat_RigControl #FoxAndHound

I recently had my shack completely torn down to have basement waterproofing I disconnected everything, marked all the connectors and put it all away for safekeeping. Now I have everything set up again

#Cat_RigControl #macOS #Elecraft

Bill, I set the radio to DATA A mode using the radio controls and verified that both VFO's were in fact set to DATA A. Then, tuned to an arbitrary frequency on 15M. Put the radio into CW mode. Pressed

#Elecraft #Cat_RigControl

MIKE - Suggest you take a more careful look at what change was required where in the old 1947 NEC revisions. It did NOT refer to having today's third U-shaped ground pin, they simply required that the

#Cat_RigControl #IssueReport #protocol #Yaesu

With me, I'm noticing just lately that the TX frequency logged is different than the dial frequency no matter what my VFO uses are (settings are). Is that correct? Thanks, Kevin, K7KSH

#Cat_RigControl #Yaesu

I'm with you on this Bob. Much ado about very little. Goodness, we can't change the mode from USB-D or DATA-U or whatever to RTTY? As far as I can tell, if I use Winwarbler, FLdigi, DM780 or other pro

#Cat_RigControl #Windows10 #WSJTX_config

Lots of RFI issues on the forum, one solution never mentioned is loose PL259 connector. I had that happen to me, if only finger tight I find they tend to loosen themselves up over time. I use a small

#Cat_RigControl #IssueReport #protocol #Yaesu

Cliff, The frequency that’s logged is the TX frequency PLUS the audio offset, so the actual frequency of transmission NOT the dial frequency. 73 Phil GM3ZZA Sent from Mail for Windows

#Cat_RigControl

Alright, problem solved. Big thanks to Mike for the debugging. Turns out it was a failure between the PC and the id10t interface, aka dying mouse. Clicked on the poor fellas left ear one too many time

#IssueReport #Yaesu #Cat_RigControl #transmit

Hi all, Have had absolutely no luck with WSJTx, so changed to JTDX and no problem, working just fine. Have made many contacts. Not sure why JTDX is working and WSJTx is not, but a good outcome for me

#Icom #Cat_RigControl

Eddy, Check the firmware version installed in the Icom 7800 and compare it with the version expected by hamlib. Icom made major changes beginning with v 3.10 for the 7800. Some software now expects v

#Cat_RigControl

I was trying to ask the original poster , who mentioned they were having trouble with wsjt and flrig.... he was having trouble with json files, but posted to wsjt group. maybe he posted to wrong group

#Cat_RigControl

Dave, All I use with my 590SG is the USB cable. I start N3FJP first then start WSJT and they talk, control the 590, do a QRZ lookup & log each contact. No DB9 cable used at all and no ARCP software us

#Cat_RigControl #Kenwood

Hi Gino, Glad to hear that all is working well. Would love to do EME, but I do not have the appropriate gear. Enjoy the FT991, its a fine radio. 73, Sam W2JDB

#Cat_RigControl

Sorry to all involved for not following up sooner. I had surgery Friday, so it's a decent excuse. I can't recall exactly how I resolved this, but I installed JTDX to see if I could get that working wi

#Cat_RigControl #Windows10

Hi all, Re-examining my whole set-up I realised that the problem only happened when I had CQRlog open. CQRlog spawns rigctld to control the 7300 _BUT_ I also had WSJT configured to talk to the 7300 di

#Cat_RigControl

If only it was that simple. Not a solution in this case. That comment refers to programmatically setting mode. Not a user operation. 7 3 Bob N2SCJ

#Cat_RigControl

Tnx Mike! That fixed it. 73 Tom KD6TR

#Cat_RigControl #signalink

Yes it will. Will be in hamlib 4.3.1 Mike W9MDB

#Cat_RigControl #Icom