I thought the band hopping issue had been solved after V2.2.2 but when I started a complete schedule (all HF bands active for all 4 timeframes) with my FT450D connected via SCU-17 interface the rig st

#WSPR #BugReport

Message: Rig.C(1286): Rig_get Freq return while getting current frequency Also, note I have done a reset on the 7200 in addition to the things previously mentioned, with no resolution. And have reinst

#BugReport

Hi Joseph, please report the full error messages. You can copy the full error message text to the Windows clipboard by hitting Ctrl+C as soon as the error message pops up. 73 Bill G4WJS.

#BugReport

WSJT-X V. 2.3.0 Win 10 Pro 64 Bit Icom IC-7200 WSJT_X has been working fine for about 2 years. Last few days, I am getting error messages whenever I try to start it. "Rig.C (1826) Rig_get frequency re

#BugReport

Hi Bruce 2 channel audio is selected, same as you indicated. Two instances of MSHV run without any problem on L and R. Only WSJT gives issues. 73 Henk -------- Oorspronkelijk bericht -------- Van: Bru

#AudioIssues #BugReport

Hi Joe It is not a K3s issue. Other applications using K3 main/sub audio are working fine. It is only WSJT that gives no difference between L and R audio. The other applications do that on the same US

#AudioIssues #BugReport

hi Pascal if its the same issue i have on windows, to get wspr to work, start wsjt-x, change mode to wspr, immediately make sure BANDHOP box is unchecked and make sure you are not TX once it has compl

#BugReport #wsjt-x-crashing #WSPR

I tried listening to WSPR on 80m with wsjt-x 2.4.0-rc1 on Mac (Big Sur 11.2.1 Intel64). It crashes within 20 seconds or so. Tried multiple times. Pascal AC7N

#BugReport #wsjt-x-crashing #WSPR

Henk, I have a IC7610 and it has a stereo L/R RX out CODEC chip. I select on the Advanced tab for the 7610 Sound property a 2 channel 16 bit 48000 Hz (DVD Quality). I have had WSJT-X on the left chann

#AudioIssues #BugReport

The K3 will have the same audio on L/R channels unless the sub RX is turned on. What is the CONFIG:Line Out setting in your K3S? 73, ... Joe, W4TV

#AudioIssues #BugReport

Hi Rieno I am using a K3s with USB audio out. The K3s has a main and sub receiver with separate L and R audio. 73 Henk -------- Oorspronkelijk bericht -------- Van: Reino Talarmo <reino.talarmo@kolumb

#AudioIssues #BugReport

Henk, Just for interest which USB audio device you are using for your USB input? Is it a rig, Signalink or similar or some audio dongle? If the last one, which type or maker? 73, Reino OH3mA

#AudioIssues #BugReport

Henk, several other users and I have confirmed that WSJT-X correctly reads from stereo channels as specified in the "Settings->Audio" panel. My test was rigorous and found no fault in the implementati

#AudioIssues #BugReport

Bill, Good to hear there is no problem in WSJT. However, my problem is WSJT specific. All other applications work OK with the same WIN10 settings/ports. So the question becomes: - where and in what fi

#AudioIssues #BugReport

Henk, I have just double-checked this using a tone generated by Audacity and played by through VAC to WSJT-X. I can select left channel input in "Settings->Audio" and swing the playback balance in Aud

#AudioIssues #BugReport

Works as designed here using K3 and microHAM MK III. Suggest you investigate your audio device and Windows settings further. Microphone inputs are notorious for ignoring settings and operating in sing

#AudioIssues #BugReport

Henk Works for me on 2.3.0. Have you got the Sound Properties configured correctly? Sometimes a "Mic" is mono, you have to get "Line In" working. 73 Alan G4ZFQ

#AudioIssues #BugReport

It is not possible to choose Left or Right audio channel in 2.3.0. and 2.4.0 rc1. Both audio channels have the same content. Using USB audio input. Other applications have no difficulty using the same

#AudioIssues #BugReport

Chris & Reino I did check this issue by simulation, see below, no problem was detected. Amos 4X4MF

#FT4 #BugReport

>I have to disable TX manually select the next transmission, then re-enable TX. If I'm quick enough, I can select the next step before it starts transmitting. Chris, Do you mean that ”Now” buttons don

#FT4 #BugReport