Hi Chris, that output is less than there should be. I would expect each device to appear twice, the second one with a "Wave ID". For example here is what I see on my system: C:\build\temp>\Users\bill\

#AudioIssues #Cat_RigControl #BugReport

Thank you for the reply, Bill. Since last post I did another "hail mary" by uninstalling and deleting all the folders including those in appdata, and downloading a fresh copy. This gave me a fresh ins

#AudioIssues #Cat_RigControl #BugReport

For Q65 it looks like using configurations is a must. On the graph you need to set it to ‘Q65’ - if you just change mode the graph mode does not change. It works fine with a configuration. Tom GM8MJV

#BugReport

Thanks for the reply, Charlie, I'll look into setting up different configurations as well. Cheers - Dave (G0DJA)

#BugReport

correction for 'f' read 'g'. There is also no 'g' in Q65, although it is selectable in -rc1.

#BugReport

Hi David I think that's happening because you were on a submode letter (f) when in JT4 and when going to Q65 that would have persisted as the selected submode. There is currently no f submode coded in

#BugReport

It was happeneing to me yesterday when trying to decode a couple of 23cm beacons that run JT4g. I'm running Windows 10 Pro on an Intel i5, 3.2GHz with 4GB RAM, if that helps? Today, when I swapped fro

#BugReport

Hi Chris, the (Not found) annotation means exactly what it says. The underlying Qt framework functionality we use to enumerate audio devices did not list the one you last used in WSJT-X. If the drop d

#AudioIssues #Cat_RigControl #BugReport

I think it would be better to focus on the bigger issue which is the sound card problem. Note this capture. The correct card shows initially as "not found". If I click on the pick list (which I did on

#AudioIssues #Cat_RigControl #BugReport

Hi Bill, After using the "Tune" button, you can't just click "Enable Tx" and expect it to work because more than half the time it doesn't. I've tested Gene's workaround (using "Halt Tx" to stop tuning

#BugReport

This is the TUNE Toggle bug I have reported in the past. The best solution offered by Joe Taylor was to not toggle the TUNE but rather click the Halt Tx button to stop tuning. This resolves the bug be

#BugReport

Chris, ID is a valid query on most modern Kenwood and Yasesu rigs, Hamlib uses that command as a way of verifying commands with no conformation response have been completed. If an ID command is not re

#AudioIssues #Cat_RigControl #BugReport

Thanks Bill, then all the work I did setting levels for TX and TUNE for each of 12 configurations by band was a good idea. It just so happens, that each of my configurations is by MODE. Makes for simp

#BugReport

Hi Hasan, all settings are stored independently for each configuration. Settings are not stored per mode, your Tune power settings should not change when you only change mode. 73 Bill G4WJS.

#BugReport

New information courtesy of "Serial Port Monitor": For some reason, wsjt-x is now sending the wrong status query string to the radio! It is sending ID; (that's I D semicolon). The correct query is IF;

#AudioIssues #Cat_RigControl #BugReport

A related question: If you have more than one configuration, do you have to calibrate Tx and Tune by Band for Each configuration? I just went through that process this afternoon and it doesn't seem to

#BugReport

Hi Ken, I'm not sure I see the link your subject implies, are you saying that disabling the recall Tx and Tune power by band options fixes this issue? 73 bill G4WJS.

#BugReport

I have two rigs currently running WSJT-X v2.3.0. One is an ICOM IC-7300 v1.3 The other is a Yaesu FTDX10. Because I use external antenna tuners on both, I have checked both the "Transmit" and "Tune" c

#BugReport

Com ports are also affected. Basically all I/O is broken. MixW4 works fine and I can make FT8 contacts with it. Last week, wsjt-x was working fine. The interface to the rig is serial via a rig blaster

#AudioIssues #Cat_RigControl #BugReport

That has nothing to do with audio ... that's a CAT control error. As far as sound cards, what are you using for a sound card? Built in card, USB soundcard, etc? Neil, KN3ILZ

#AudioIssues #Cat_RigControl #BugReport