From your screen capture, it appears that your waterfall zero slider and waterfall gain slider are too far to the right. Mine run about the 3rd bar from the left of the scale. The RF Gain on the radio

If the audio is to low out of the computer then it won’t key the PTT in the Signalink. The slider in WSJT will control that level. Then one adjust the TX control on the Signalink for the correct audio

I would first check all PL-259 connectors to assure they are correctly mated and are very tight. Any that appear suspicious, replace them. Also, add a common mode choke to the coax from the antenna. A

As to monitoring, yes the FCC has jurisdiction for the US while other Monitoring Services have jurisdiction in other countries. As to monitoring one's signal, most radios have a MONITOR function which

#FT8

QRZ.COM does allow the USER to enter and edit his location and Grid Square. In general, if it is not correct it is because the user has moved and not updated the database, or just forgot to do so. I j

#FT8

When working digital modes, why have the volume turned up on the receiver? If someone is transmitting voice in a Digital or CW band, it is their problem and and the Monitoring Services and FCC can and

#FT8

I run Windows 10 Pro 64 bit version on both laptops and have done so for quite some time. I did not and have not experience any sound configuration changes after any of the recent updates. One compute

Since you have the USB Audio CODEC at MAX and you have the WSJT-X PWR slider set to max, I suggest and agree with Chuck, set the power on the radio to 100 watts and adjust the Line Gain on the radio f

#FT8 #FT4

Depending on the rig. With some radios, it is best to set the PWR for 100 watts and adjust the Line Gain on the radio for the desired power output. This assures the PWR slider, which actually changes

I use Windows 10 Pro running on my laptop for my station computer. I accept all the Windows updates automatically. I can't recall the last time I had an issue with any of the applications that use aud

In using my Elecraft K3S or my Tentec Eagle, I do not observe any delay between RX to TX or when switching from TX to RX when using the SPLIT mode. In both instances, the radio is connected directly t

When using SPLIT with CAT control it switches VFO B to the desired frequency to perform as Gary - AG0N described. When you use "Fake It" then it only uses VFO A and changes that frequency between RX a

If you wish to work MS on 10M then CW is the proper and correct mode to use. I've done it that way for years. FT-8, due to the symbol rate, is not legal to use on 10M. From a former FCC enforcement of

As to Duty Cycle, look at your manual in the specifications section. Mine says 100% for 10 minutes, 100 Watts key down, for CW and SSB modes. I frequently run 100 watts in FT-8 mode. PA temp will rise

Gentlemen: The bottom line is this; "MSK144 and MSK144sh are not permitted on MF, HF or 10 meters because the symbol rate is greater than 300 baud." This is the current FCC regulation regarding spectr

A better approach is not to use NR or NB on the receiver but to use a combination of attenuation and RF gain reduction. Ideally the “no signal” band noise should be about 10dB above the noise floor of

#FT8

If one uses their computer to play video or audio, that or those applications can change the sound card settings. When one goes to WSJT-X one may have to reset the settings for WSJT-X. I have been usi

#AudioIssues

The Signalink USB has its own internal VOX circuit activated by the computer audio to generate a relay closure for PTT. It DOES NOT rely on the VOX on the radio. As to any shortcomings of the circuit,

I have tried several calls as decoded and first pressing escape and then entering the call into the Call box and then tapping Look Up. The message appears "not in the Call3.TXT. Likewise when I manual

I find that 14.071 along with 14.074 is in the frequency table for FT-8. That gives almost 6 kHz useable bandwidth. Yes, 14.074 is quite busy. So guess we have to spread out a bit. 73 Bob, K4TAX