Hello Dennis, My screen reader isn't confirming the attachment. https://www.dropbox.com/s/sl62490dd782kov/SIGNALINK_USB_CONNECTING_TO_KENWOOD_TS-2000.pdf?dl=1 Georgina Call: M0EBP DMR ID: 2346259 Alls

#AudioIssues

Hello Dennis, Here's the document I got from SL. 73 Georgina Call: M0EBP DMR ID: 2346259 Allstar: 52178 Locater: IO83PS

#AudioIssues

Hello Dennis, I have used a TS-2000 but with a SL USB. So have you connected the 2000 via the serial port and have that working for cat control? The audio line is a separate line and I would suggest y

#AudioIssues

Hello Jim, With my FT-818 I need to use 2 cables and I am not sure if you will do too. You might need to get an interface of some kind like a SL USB. See this thread: https://www.eham.net/article/2800

#install #Cat_RigControl

Hello Jim, You haven't stated what operating system you are using. You mention chirp which leads me to linux but chirp can be run on other operating systems. So you need to identify what port the cabl

#install #Cat_RigControl

Hello, I am struggling with this too. I have TS-590SG. I know my cable connection provides this output: sources: alsa_output.usb-Burr-Brown_from_TI_USB_Audio_CODEC-00.analog-stereo.monitor/#3: Monitor

Hello, Regrettably, it appears it is a GTK application. I want to see if it has a command line interface. While graphical interfaces suit and are appreciated by most people. All that computer power is

Hello Bill, 73Thank you I shall check it out. Georgina Call: M0EBP DMR ID: 2346259 Allstar: 52178 Locater: IO83PS

Hello All, I installed WSJT-X on a Raspberry Pi 400 as I wanted to see if orca screen reader could enable me to navigate the interface. I am glad to say I have been able to set my call and grid. Set m

Hello All, Thanks for your suggestions. I just had a goal to get a number of contacts before the end of the year. As I write I have a few hours left of this year. But have given up and will look to se

Hello All, I have noticed I can get contacts quite easily during daylight time, typically 20m and on 40m. I have observed 20m goes flat slowly after sunset. On 40m and 80m where I can hear activity du

Hello, I have had the same happen here. I am looking at the Windows mixer controls. I found my record level was at 100%. Lowering it has brought back decoding but it is still not right. Being a blind

Hello, This sounds cool. Pity about the headless observation. I wondered how much does that system need from the power supply? Does the SSD require a lot of power? Or do power the enclosure? Thanks, 7

Hello, Are you sure that your USB cable connection is comm3? I don't think I have seen a USB serial device allocated a 1 - 4 assignment. As these were for the traditional 25 / 9 pin serial ports. You

Hello, If you have followed the document by Kenwood I can only assure you it worked straight away for me. Also note that the document states to do a reset so all settings are at default then it states

Hello, Kenwood have published a document and I couldn't find where I have stored its URL. But here's a link to my dropbox. The setting worked for me. https://www.dropbox.com/s/i4q9mc4klaz8ad2/ts590_sg

Hello, Interesting. Here in the UK 3.573 is very busy come nightfall. 73 Georgina Call: M0EBP DMR ID: 2346259 Allstar: 52178 Locater: IO83PS

Hello, That would be nice to resolve all our accessibility problems. 73 Georgina Call: M0EBP DMR ID: 2346259 Allstar: 52178 Locater: IO83PS

Hello John. What an interesting post. Reading through I decided to reply. Because being blind I listen to a speech interpretation of the call and grid. Believe me there have been times when I have tho

#FT8

Hello Bill, Thank you for an educational post. However, I raised the issue because of my antenna location. I am sitting quite close to it and don't fancy washing myself and neighbours with RF. As FT8