main@WSJTX.groups.io

Home Messages Hashtags Subgroups

Expanded

Between

and

Re: Freq jumps 500 at a time. .7300>>>72500 #frequency Robie - AJ4F #32929 Good Morning, I believe your system is operating properly. Take a look a section 4.2 of the Users Guide for an explanation: https://physics.princeton.edu/pulsar/k1jt/wsjtx-doc/wsjtx-main-2.5.4.html Robie AJ4F On Fri, Mar 18, 2022 at 3:26 AM Buffalo Berger <buffaloberger@...> wrote: Hello im running a ft891 signalink and windows 11. I used kb9vbr YouTube video to set up everything and it works flawlessly. Except the freq wants to walk down the band 500 KC at a time. Is there away to stop this. A different config or something?
More All Messages By This Member
Re: configure SignalLink #windows11 Stanley Engel #32928 Thanks guys. As far as the wiring goes, it is correct because I have been using this setup on a Win10 laptop for a few years now. The only difference is the new Win11 laptop. And the Codec driver shows up in the Device Manager. I will work some more on it later today, it has to be something I am doing wrong. I have never dealt with "permissions" before so that could be an issue. Stan – WA2UET In Ghent NY toggle quoted message Show quoted text -----Original Message----- From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Buffalo Berger Sent: Friday, March 18, 2022 3:45 AM To: main@WSJTX.groups.io Subject: Re: [WSJTX] configure SignalLink #windows11 I have a signalink and yaesu 891. Windows 11. Windows 11 works great with the signalink. However, every time I look for audio device CODEC just after plugging it in it says... Audio Codec (not found). Unplug and replug in usb from signalink to the computer say in Fldigi app. Under audio then they appear without the (not found). So that being said if you do not see audio codec then my guess would be the signalink jumpers are not correct. Signalink will provide the correct jumper config if you contact them. If it's still a problem I would agree that the wiring from signalink to the radio is wrong. If signalink doesn't have that info you can find it online. Or ask someone for a diagram and help getting it right. Should be pretty straight forward.
More All Messages By This Member
Re: Can I adjust the listening frequency in WSJTX? #WSPR Pietro Molina #32927 On Fri, Mar 18, 2022 at 01:48 AM, Mark, WD4ELG wrote: Sorry if I wasn't clear before. Here's a waterfall picture of the audio output from my CW rig. Note that the audio is nowhere near the 1400-1600 Hz listening sweet-spot for WSPR. [cid:image001.png@...] Mark Lunday, WD4ELG Greensboro, NC FM06be I'll try to help you. May be some number is wrong, but only the the idea is important. If you tune, i.e., 14.040 Mhz in a USB radio, audio band will be 14,040,000 - 14,042,700 Hz. If you tune, i.e, 14.040 Mhz in a CW radio, audio band will be ~ 14,040,600 - 14,040,850 Hz. But WSJT considers the center (theoric tuning) band at 1,5 Khz, CW at ~ 800 Hz, so your pass band is shifted of about 700 hz and you will have a bandpass of ~250 hz centered at 1500Hz for WSJT. You will receive 1.4-1.6 khz, as you said. To deconde, i.e., my signal at 500 Hz you need shift the tuning down of 1 kHz. I hope it's clear, it's more difficult to explain in writing that it actually is. Try to tune 14.039 Mhz and you will receive the 400-600Hz segment of WSJT 20 meters band (conventionally at 14.040 Mhz). Pietro I2OIM .
More All Messages By This Member
Logging issue #logging Buffalo Berger #32926 Hi I just made my 1st 11 or so contacts and logging everything works great. But I'm using dxkeeper as my primary log. I don't mind syncing lotw and eqsl. That's not the problem. Lotw says all logs are correct and they're downloaded. Eqsl States that x was uploaded and 0 errors and x rejected. X=8 Then checking dxkeeper log page they are not written into the log from any service. Except 1 that I did by accident. I did check the box [change mode to rtty] Any help.?
More All Messages By This Member
Freq jumps 500 at a time. .7300>>>72500 #frequency Buffalo Berger #32925 Hello im running a ft891 signalink and windows 11. I used kb9vbr YouTube video to set up everything and it works flawlessly. Except the freq wants to walk down the band 500 KC at a time. Is there away to stop this. A different config or something?
More All Messages By This Member
Re: Behavior change doesn't disable transmit #IssueReport #TechnicalHelpQuestion Dennis Wage <dwage@...> #32924 If your transmit freq is set to 1500. Split or not you’ll be in the 1500-1550 slot. Split does absolutely nothing to change this. On Thu, Mar 17, 2022 at 19:48 Robert Lorenzini <bob@...> wrote: Folks please use split. Bob - wd6dod On 3/17/2022 8:40 AM, neil_zampella wrote: Basically ... If you are trying to answer a CQ caller on their frequency (or within 50 (??) hz) WSJT-X will stop your Tx to reduce any QRM. If you do as Dennis advised, and find a clear frequency and Tx off the caller's location, and set HOLD TX FREQ, you're not going to cause QRM to that caller, and the program will continue to send your reply. Neil, KN3ILZ On 3/17/2022 8:14 AM, Dennis Wage wrote: It’s happened to me. And somehow WSJT-X can detect when one ore more users are using the same 50hz slice and it will disable transmit. I may have described this wrongly and used bad terminology but I believe this is it. Solution: ALWAYS have ‘Hold Tx Freq’ checked and ALWAYS check your waterfall for an open 50hz slot to operate. ‘Hold Tx Freq’ shouldn’t be an option, it should be the default. On Thu, Mar 17, 2022 at 07:36 chas cartmel <chas@...> wrote: William, have you responded to the right message?Your answer is not relevant to what the OP has pointed out.-----Original Message-----From: main@WSJTX.groups.io [mailto:main@WSJTX.groups.io] On Behalf Of William SmithSent: Thursday, March 17, 2022 11:10 AMTo: main@...: Re: [WSJTX] Behavior change doesn't disable transmit #TechnicalHelpQuestion #IssueReportIf you are transmitting on the same audio frequency as someone else (and if you haven’t checke' ‘Hol' Tx’, when you click on a 'Q, it’ll move your transmit frequency to that of the caller, so you _are_ transmitting on the same audio frequency), this will happen to reduce QRM.The solution is t' check ‘Hold Tx’ and pick a spot on the wa'erfall that’s visually clear () for your transmission.73, Willie N1JBJ() I use a Python program to look through the last 2 minutes of ALL.TXT and search for open frequencies even if they are not visually detectable on the water'all, but that’s overkill, and a bit "f a kludge, so “Looks Clear To Me” is a perfectly fine paradigm.> On Mar 17, 2022, at 4:42 AM, Nige Barker < Nigel.barker@...> wrote:> > Hi> > Previously I have noted that if I'm trying to reply to a station, and> someone else replies to that station, Enable Transmit is deselected.> > Now it doesn't seem to be.> > Just checking if this is the expected behavior.> > Kind regards> > Nigel> M0HZR> > > > > ?? This email has been scanned by BullGuard antivirus p <https://www.google.com/maps/search/email+has+been+scanned+by+BullGuard+antivirus+p?entry=gmail&source=g> rotection. For more info visit www.bullguard.com -- Dennis M. Wage (W9BOQ) 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 https://www.grammy.com/grammys/artists/dennis-wage/252054 http://overdubs.net -- Dennis M. Wage (W9BOQ) 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 https://www.grammy.com/grammys/artists/dennis-wage/252054 http://overdubs.net
More All Messages By This Member
Re: configure SignalLink #windows11 Buffalo Berger #32923 I have a signalink and yaesu 891. Windows 11. Windows 11 works great with the signalink. However, every time I look for audio device CODEC just after plugging it in it says... Audio Codec (not found). Unplug and replug in usb from signalink to the computer say in Fldigi app. Under audio then they appear without the (not found). So that being said if you do not see audio codec then my guess would be the signalink jumpers are not correct. Signalink will provide the correct jumper config if you contact them. If it's still a problem I would agree that the wiring from signalink to the radio is wrong. If signalink doesn't have that info you can find it online. Or ask someone for a diagram and help getting it right. Should be pretty straight forward.
More All Messages By This Member
Re: configure SignalLink #windows11 Reino Talarmo #32922 Hi Stan, In short the "I see only vertical stripes" indicates that WSJT-X does not get any audio and tries to present zero values of something similar. You have various possible reasons for this situation. The USB connection to the Signalink is not established or Signalink does not receive any audio from your rig. You may try to disconnect USB cable and see whether the USB codec disappears and re-appears at plugging USB back. The connection to your FT450 from Signalink depends on the cable to the DATA connector needs to be properly wired and I have an impression that there is also settings and wirering inside the Signalink that of course need to be correct. The last issue is Windows audio settings and security permissions, but 11 may be a bit different than 10 and I have only 10. 73, Reino OH3mA
More All Messages By This Member
Re: Can I adjust the listening frequency in WSJTX? #WSPR Mike Black #32921 Looks like a 250Hz wide CW filter centered on 600 -- not surprising for CW. Now seeing your filter width I'm afraid you're out of luck with that rig and WSJTX in any mode.You could get the WSPR signals within your filter width by increasing the WSPR frequencies 900Hz in the Frequencies tab...but they won't decode down there. I'm afraid you're out of luck. Do you just want to decode or transmit too? Mike W9MDB toggle quoted message Show quoted text On Thursday, March 17, 2022, 07:48:47 PM CDT, Mark, WD4ELG <wd4elg@...> wrote: Sorry if I wasn't clear before. Here's a waterfall picture of the audio output from my CW rig. Note that the audio is nowhere near the 1400-1600 Hz listening sweet-spot for WSPR. [cid:image001.png@...] Mark Lunday, WD4ELG Greensboro, NC FM06be wd4elg@...<mailto:wd4elg@...> http://wd4elg.blogspot.com SKCC #16439 FISTS #17972 QRP ARCI #16497
More All Messages By This Member
Re: Can I adjust the listening frequency in WSJTX? #WSPR Dennis Wage <dwage@...> #32920 Picture is very low resolution. But I think you should be able to do the math and detune your receiver manually and end up transmitting and receiving right where you want. On Thu, Mar 17, 2022 at 19:48 Mark, WD4ELG <wd4elg@...> wrote: Sorry if I wasn't clear before. Here's a waterfall picture of the audio output from my CW rig. Note that the audio is nowhere near the 1400-1600 Hz listening sweet-spot for WSPR. [cid:image001.png@...] Mark Lunday, WD4ELG Greensboro, NC FM06be wd4elg@...<mailto:wd4elg@...> http://wd4elg.blogspot.com SKCC #16439 FISTS #17972 QRP ARCI #16497 Attachments: image001.png: https://WSJTX.groups.io/g/main/attachment/32919/0 -- Dennis M. Wage (W9BOQ) 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 https://www.grammy.com/grammys/artists/dennis-wage/252054 http://overdubs.net
More All Messages By This Member
Re: Can I adjust the listening frequency in WSJTX? #WSPR Mark, WD4ELG #32919 Sorry if I wasn't clear before. Here's a waterfall picture of the audio output from my CW rig. Note that the audio is nowhere near the 1400-1600 Hz listening sweet-spot for WSPR. [cid:image001.png@...] Mark Lunday, WD4ELG Greensboro, NC FM06be wd4elg@...<mailto:wd4elg@...> http://wd4elg.blogspot.com SKCC #16439 FISTS #17972 QRP ARCI #16497 image001.png
More All Messages By This Member
Re: Behavior change doesn't disable transmit #IssueReport #TechnicalHelpQuestion Dennis Wage <dwage@...> #32918 You’ll have to explain to me how split has anything to do with this. On Thu, Mar 17, 2022 at 13:51 Dave Garber <ve3wej@...> wrote: yes that is why most try running split Dave Garber VE3WEJ / VE3IE On Thu, Mar 17, 2022 at 6:55 AM Nige Barker <Nigel.barker@...> wrote: Hi Previously I have noted that if I'm trying to reply to a station, and someone else replies to that station, Enable Transmit is deselected. Now it doesn't seem to be. Just checking if this is the expected behavior. Kind regards Nigel M0HZR -- Dennis M. Wage (W9BOQ) 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 https://www.grammy.com/grammys/artists/dennis-wage/252054 http://overdubs.net
More All Messages By This Member
#FT8 #Cat_RigControl #AudioIssues #Icom #Windows10 #AudioIssues #Icom #Windows10 #FT8 #Cat_RigControl Kerry Webster WB7AKE #32917 I have no IC-7300 transmit power on FT8. Have been running FT8 for three years on IC-7300 from Windows 10 laptop with no problems. But laptop gunnysacked and had to replace it. Downloaded latest WSJT-X version and got it running. Worked fine— until it didn't. It quit literally between QSOs. The PTT triggers and audio from USB Codec is heard in rig monitor, but there is no RF output. Trace shows on touchscreen as if transmitting, but there is no ALC indication. Rig operates normally in all other modes, full output, normal ALC. One clue: just before the rig quit on FT8, I noticed the ALC meter acting oddly — it would spike to full, then gradually fall off until about 1/4 value. I have checked and double-checked all the Windows sound settings, and they all appear nominal. The only anomaly I can see is that the USB Codex has a prefix: 2-USB Codex. Not sure what that's about. Anyone have any ideas? Regards.
More All Messages By This Member
Re: Behavior change doesn't disable transmit #IssueReport #TechnicalHelpQuestion Robert Lorenzini #32916 Folks please use split. Bob - wd6dod toggle quoted message Show quoted text On 3/17/2022 8:40 AM, neil_zampella wrote: Basically ... If you are trying to answer a CQ caller on their frequency (or within 50 (??) hz) WSJT-X will stop your Tx to reduce any QRM. If you do as Dennis advised, and find a clear frequency and Tx off the caller's location, and set HOLD TX FREQ, you're not going to cause QRM to that caller, and the program will continue to send your reply. Neil, KN3ILZ On 3/17/2022 8:14 AM, Dennis Wage wrote: It’s happened to me. And somehow WSJT-X can detect when one ore more users are using the same 50hz slice and it will disable transmit. I may have described this wrongly and used bad terminology but I believe this is it. Solution: ALWAYS have ‘Hold Tx Freq’ checked and ALWAYS check your waterfall for an open 50hz slot to operate. ‘Hold Tx Freq’ shouldn’t be an option, it should be the default. On Thu, Mar 17, 2022 at 07:36 chas cartmel <chas@...> wrote: William, have you responded to the right message?Your answer is not relevant to what the OP has pointed out.-----Original Message-----From: main@WSJTX.groups.io [mailto:main@WSJTX.groups.io] On Behalf Of William SmithSent: Thursday, March 17, 2022 11:10 AMTo: main@...: Re: [WSJTX] Behavior change doesn't disable transmit #TechnicalHelpQuestion #IssueReportIf you are transmitting on the same audio frequency as someone else (and if you haven’t checke' ‘Hol' Tx’, when you click on a 'Q, it’ll move your transmit frequency to that of the caller, so you _are_ transmitting on the same audio frequency), this will happen to reduce QRM.The solution is t' check ‘Hold Tx’ and pick a spot on the wa'erfall that’s visually clear () for your transmission.73, Willie N1JBJ() I use a Python program to look through the last 2 minutes of ALL.TXT and search for open frequencies even if they are not visually detectable on the water'all, but that’s overkill, and a bit "f a kludge, so “Looks Clear To Me” is a perfectly fine paradigm.> On Mar 17, 2022, at 4:42 AM, Nige Barker < Nigel.barker@...> wrote:> > Hi> > Previously I have noted that if I'm trying to reply to a station, and> someone else replies to that station, Enable Transmit is deselected.> > Now it doesn't seem to be.> > Just checking if this is the expected behavior.> > Kind regards> > Nigel> M0HZR> > > > > ?? This email has been scanned by BullGuard antivirus protection. For more info visit www.bullguard.com -- Dennis M. Wage (W9BOQ) 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 https://www.grammy.com/grammys/artists/dennis-wage/252054 http://overdubs.net
More All Messages By This Member
Compile error on Arch Linux after updating packages #linux cybermike #32915 Hello! I recently updated the packages on my Arch Linux system and can no longer compile WSJT-X (issue is present on versions 2.5.4 and 2.5.2). My kernel version is 5.16.14. I believe a QT update may be the culprit, but I could be wrong. Compiler output is as follows: [ 85%] Linking CXX static library libwsjt_qt.a [ 85%] Built target wsjt_qt [ 85%] Automatic MOC for target fort_qt [ 85%] Built target fort_qt_autogen [ 85%] Building CXX object CMakeFiles/fort_qt.dir/fort_qt_autogen/mocs_compilation.cpp.o [ 85%] Building CXX object CMakeFiles/fort_qt.dir/lib/shmem.cpp.o [ 85%] Linking CXX static library libfort_qt.a [ 85%] Built target fort_qt [ 85%] Automatic MOC for target wsjt_qtmm [ 85%] Built target wsjt_qtmm_autogen [ 86%] Building CXX object CMakeFiles/wsjt_qtmm.dir/wsjt_qtmm_autogen/mocs_compilation.cpp.o [ 86%] Building CXX object CMakeFiles/wsjt_qtmm.dir/Audio/BWFFile.cpp.o [ 86%] Linking CXX static library libwsjt_qtmm.a [ 86%] Built target wsjt_qtmm [ 86%] Automatic MOC for target record_time_signal [ 86%] Built target record_time_signal_autogen [ 86%] Building CXX object CMakeFiles/record_time_signal.dir/record_time_signal_autogen/mocs_compilation.cpp.o [ 86%] Building CXX object CMakeFiles/record_time_signal.dir/Audio/tools/record_time_signal.cpp.o [ 87%] Linking CXX executable record_time_signal [ 87%] Built target record_time_signal [ 87%] Automatic MOC for target jt9 [ 87%] Built target jt9_autogen Scanning dependencies of target jt9 [ 87%] Building CXX object CMakeFiles/jt9.dir/jt9_autogen/mocs_compilation.cpp.o [ 87%] Building Fortran object CMakeFiles/jt9.dir/lib/jt9.f90.o [ 87%] Building Fortran object CMakeFiles/jt9.dir/lib/jt9a.f90.o [ 87%] Linking CXX executable jt9 [ 87%] Built target jt9 [ 87%] Compressing Debian changelog [ 87%] Built target debian [ 87%] Automatic MOC for target wsjtx [ 87%] Built target wsjtx_autogen [ 87%] Generating wsjtx_zh_TW.qm Updating '/home/mike/Apps/backup/wsjtx-2.5.4/wsjtx-prefix/src/wsjtx-build/wsjtx_zh_TW.qm'... Generated 1192 translation(s) (1192 finished and 0 unfinished) [ 87%] Generating qrc_style.cpp [ 88%] Building required Qt translations for language ca [ 88%] Building required Qt translations for language da [ 88%] Building required Qt translations for language en [ 88%] Building required Qt translations for language es [ 88%] Building required Qt translations for language it QM-Format error make[5]: * [CMakeFiles/wsjtx.dir/build.make:234: qt_it.qm] Error 2 make[4]: * [CMakeFiles/Makefile2:1342: CMakeFiles/wsjtx.dir/all] Error 2 make[3]: * [Makefile:156: all] Error 2 make[2]: * [CMakeFiles/wsjtx-build.dir/build.make:73: wsjtx-prefix/src/wsjtx-stamp/wsjtx-build] Error 2 make[1]: * [CMakeFiles/Makefile2:279: CMakeFiles/wsjtx-build.dir/all] Error 2 make: * [Makefile:91: all] Error 2 Any help would be appreciated, thank you! -Mike
More All Messages By This Member
Re: DT red box #decode chas cartmel #32914 toggle quoted message Show quoted text Richard,Your original post had your call as wb6ewem, obviously a typo though.73 CharlieG4ESTwww.g4est.me.ukStay safe out there-----Original Message-----From: main@WSJTX.groups.io [mailto:main@WSJTX.groups.io] On Behalf Of richard clareSent: Thursday, March 17, 2022 4:50 PMTo: main@...: Re: [WSJTX] DT red box #decodewb6ewm is valid. Richard This email has been scanned by BullGuard antivirus protection. For more info visit www.bullguard.com
More All Messages By This Member
Re: Behavior change doesn't disable transmit #IssueReport #TechnicalHelpQuestion Chuck Gelm #32913 On 3/17/22 04:42, Nige Barker wrote: Hi Previously I have noted that if I'm trying to reply to a station, and someone else replies to that station, Enable Transmit is deselected. Now it doesn't seem to be. Just checking if this is the expected behavior. I thought is was like this; If you reply to a CQ and your TX is within 60 Hz of the calling station, and then the calling station replies to some other station, your TX will be disabled. Outside of this 60 bandwidth, your station will continue calling (x10?). 73, Chuck
More All Messages By This Member
Re: configure SignalLink #windows11 Stanley Engel #32912 It is the FT450 Dave and I use the DATA out to the signallink. Stan toggle quoted message Show quoted text -----Original Message----- From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Dave Garber Sent: Thursday, March 17, 2022 4:54 PM To: WSJT-x group <main@wsjtx.groups.io> Subject: Re: [WSJTX] configure SignalLink #windows11 which radio and how are you feeding the signalink audio FROM the radio Dave Garber VE3WEJ / VE3IE On Thu, Mar 17, 2022 at 2:42 PM Stanley Engel <wa2uet@...> wrote: I am not familiar with permissions Dave but from what I can see everything is OK. I am new to Win11! Stan – WA2UET In Ghent NY -----Original Message----- From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Dave Garber Sent: Thursday, March 17, 2022 2:24 PM To: WSJT-x group <main@wsjtx.groups.io> Subject: Re: [WSJTX] configure SignalLink #windows11 then check your permissions on the audio, maybe they are off Dave Garber VE3WEJ / VE3IE On Thu, Mar 17, 2022 at 12:54 PM Stanley Engel <wa2uet@...> wrote: There is only one codec device in the list Dave. I tried it with MMSSTV and seems to be the same issue. I don't know about a driver, I just assume Windows has installed whatever is needed. The USB Codec device shows up in the settings. Stan – WA2UET In Ghent NY -----Original Message----- From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Dave Garber Sent: Thursday, March 17, 2022 12:16 PM To: WSJT-x group <main@wsjtx.groups.io> Subject: Re: [WSJTX] configure SignalLink #windows11 sounds like you are not using the correct audio codec, or maybe rec gain is too low what about other software/modes do they react the same way if the driver is installed, I have no issue with signalink on my w11 machine Dave Garber VE3WEJ / VE3IE On Thu, Mar 17, 2022 at 11:36 AM Stanley Engel <wa2uet@...> wrote: Update... When I first start the app it works for maybe 5 seconds then stops decoding with just the red vertical strips on the water fall. This is consistent, every time I start the app... Stan – WA2UET In Ghent NY -----Original Message----- From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Stanley Engel via groups.io Sent: Thursday, March 17, 2022 10:18 AM To: main@WSJTX.groups.io Subject: [WSJTX] configure SignalLink #windows11 I am new to this group just now so i have not searched for topic. I just purchased a new Win11 laptop and installed WSJT. I cannot get the signallink to work with it. A couple of times while playing with settings it received for maybe 2 seconds. I only see the red vertical lines in the waterfall. It has worked perfectly with the old Win10 laptop. I can't figure it out, it is like the audio i/o is not there. But the computer sees the signalink OK. Could this be an issue with Win11? Thanks, Stan, WA2UET
More All Messages By This Member
Re: Can I adjust the listening frequency in WSJTX? #WSPR Mark, WD4ELG #32911 On Thu, Mar 17, 2022 at 11:23 AM, Michael Black wrote: WSPR frequencies down 800Hz Mike, please explain like I am a newbie. WSJT-X only decodes WSPR signals in the 1400-1600Hz passband. My CW receiver only passes signals between 400 and 900 Hz. How do I adjust WSPR so it is listening between 400 and 900 Hz?
More All Messages By This Member
Re: configure SignalLink #windows11 Dave Garber <ve3wej@...> #32910 which radio and how are you feeding the signalink audio FROM the radio Dave Garber VE3WEJ / VE3IE toggle quoted message Show quoted text On Thu, Mar 17, 2022 at 2:42 PM Stanley Engel <wa2uet@...> wrote: I am not familiar with permissions Dave but from what I can see everything is OK. I am new to Win11! Stan – WA2UET In Ghent NY -----Original Message----- From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Dave Garber Sent: Thursday, March 17, 2022 2:24 PM To: WSJT-x group <main@wsjtx.groups.io> Subject: Re: [WSJTX] configure SignalLink #windows11 then check your permissions on the audio, maybe they are off Dave Garber VE3WEJ / VE3IE On Thu, Mar 17, 2022 at 12:54 PM Stanley Engel <wa2uet@...> wrote: There is only one codec device in the list Dave. I tried it with MMSSTV and seems to be the same issue. I don't know about a driver, I just assume Windows has installed whatever is needed. The USB Codec device shows up in the settings. Stan – WA2UET In Ghent NY -----Original Message----- From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Dave Garber Sent: Thursday, March 17, 2022 12:16 PM To: WSJT-x group <main@wsjtx.groups.io> Subject: Re: [WSJTX] configure SignalLink #windows11 sounds like you are not using the correct audio codec, or maybe rec gain is too low what about other software/modes do they react the same way if the driver is installed, I have no issue with signalink on my w11 machine Dave Garber VE3WEJ / VE3IE On Thu, Mar 17, 2022 at 11:36 AM Stanley Engel <wa2uet@...> wrote: Update... When I first start the app it works for maybe 5 seconds then stops decoding with just the red vertical strips on the water fall. This is consistent, every time I start the app... Stan – WA2UET In Ghent NY -----Original Message----- From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Stanley Engel via groups.io Sent: Thursday, March 17, 2022 10:18 AM To: main@WSJTX.groups.io Subject: [WSJTX] configure SignalLink #windows11 I am new to this group just now so i have not searched for topic. I just purchased a new Win11 laptop and installed WSJT. I cannot get the signallink to work with it. A couple of times while playing with settings it received for maybe 2 seconds. I only see the red vertical lines in the waterfall. It has worked perfectly with the old Win10 laptop. I can't figure it out, it is like the audio i/o is not there. But the computer sees the signalink OK. Could this be an issue with Win11? Thanks, Stan, WA2UET
More All Messages By This Member

11841 - 11860 of 44369

Home Hashtags Subgroups About Features Pricing Updates Terms Help Twitter