|
Locked
Re: WSJTX with rig control
#WSJTX_config
Howard Kunkel
Trying to fix my no output problem I dug a little deeper in device manager. Opening each usb hub and viewing DETAILS TAB. I discovered many USB hubs were disabled! Turning them on and repeating for each device attached to that hub helped resolve the issue. The "+" indicator is very small drilling down past the USB hub. Howie WA2AGA I am also getting a Rig Control Error |
|
|
|
Locked
Re: Microphone going to sleep?
Yes... I checked everything dealing with USB...
Herb Blue might have it identified... I'll have to look at that also... Thanks |
|
|
|
Locked
Re: V2.1.1 settings menu page will not fit raspberry pi display
On 17/04/2020 01:03, Bob Watson via groups.io wrote:
I installed V2.1.1 on my raspberry pi 4B with a waveshare 7 inch hdmi display. The first screen displays properly. When I go to the Settings screen, I am able to input all the required data. However, the page is too large to see the Save button and I am not able to retain the settings. I tried to move the page around the screen. I could move the page from side to side but not up and down enough to see the Save button. This is the only page I have this problem with. All other installed apps display properly.Hi Bob, the default action is "Ok" so just hit ENTER. 73 Bill G4WJS. |
|
|
|
Locked
V2.1.1 settings menu page will not fit raspberry pi display
Bob Watson <kn4hhptc@...>
I installed V2.1.1 on my raspberry pi 4B with a waveshare 7 inch hdmi display. The first screen displays properly. When I go to the Settings screen, I am able to input all the required data. However, the page is too large to see the Save button and I am not able to retain the settings. I tried to move the page around the screen. I could move the page from side to side but not up and down enough to see the Save button. This is the only page I have this problem with. All other installed apps display properly.
I would appreciate any assistance. 73, Bob, KN4HH |
|
|
|
Locked
Re: Hamlib error
#WSJTX_config
Bob Lewis
I occasionally have that issue with my IC756PRO. Clicking on the [retry] button on the message box always clears it without causing any other problems.
toggle quoted message
Show quoted text
-----Original Message-----
From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of Don Roden Sent: Thursday, April 16, 2020 7:45 PM To: WSJTX@groups.io Subject: Re: [WSJTX] Hamlib error #hamlib #WSJTX_config My TS-2000 does that when the sub receiver is turned on ... off = fine. Don W4DNR Quoting "zs6bv via groups.io" <zs6bv@...>: Rig Control Error |
|
|
|
Locked
Re: Microphone going to sleep?
Bob Lewis
Here’s a link on how to do this in the latest W10 version: https://www.windowscentral.com/how-prevent-windows-10-turning-usb-devices
From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of Mack Edmonson via groups.io
Sent: Thursday, April 16, 2020 5:21 PM To: WSJTX@groups.io Subject: Re: [WSJTX] Microphone going to sleep? #wsjtx
I think you will find power management in DEVICE MANAGER< USB CONTROLLERS, un tick the “ Allow the computer to turn off this device to save power” Do this for each device under USB controllers. Good Luck Mack, W4ENN
Sent from Mail for Windows 10
|
|
|
|
Locked
Re: Hamlib error
#WSJTX_config
Don Roden
My TS-2000 does that when the sub receiver is turned on ... off = fine.
toggle quoted message
Show quoted text
Don W4DNR Quoting "zs6bv via groups.io" <zs6bv@...>: Rig Control Error |
|
|
|
Locked
Re: GPS satellite time sync is wonderful
I followed your instructions. The NMEATime Panel says "No GPS". I may need "SiRFDemo" to switch the GPS from SiRF back to NMEA.
Does anyone know where I can find this program to download? Has anyone heard of a different fix? There is also a similar problem with USB GPS receivers. They work on Windows 7, but not on Win 8 and 10. |
|
|
|
Locked
Re: Constand Rig Control Error
Paul Hamilton <Ke7uae@...>
Can you run WSJT-X radio config with no radio control and VOX PTT ? That is how I run my Elecraft K2 using rig control is a luxury unless you need it for PTT. Good luck, KE7UAE
|
|
|
|
Locked
Re: WSJTX with rig control
#WSJTX_config
On 16/04/2020 19:56, zs6bv via groups.io wrote:
I am also getting a Rig Control ErrorHi OM, with the Yaesu FT-817/857/897/818(D) series of rigs you must uncheck the WSJT-X option "Settings->General->Allow Tx frequency changes while transmitting". 73 Bill G4WJS. |
|
|
|
Locked
Re: Constand Rig Control Error
On 16/04/2020 13:48, Gary Shirk via
groups.io wrote:
Hi Gary, the SignaLink USB interface is audio and PTT only, it does not
provide a CAT control connection. If you do not have an additional
CAT interface for your FT-847 then you need to select the WSJT-X
option "Settings->Radio->Rig->None". You also need to set
the option "Settings->Radio->PTT Method->VOX". 73 |
|
|
|
Locked
Re: WSJTX with rig control
#WSJTX_config
zs6bv@...
I am also getting a Rig Control Error
Hamlib error: Command rejected by the rig while setting frequency It happens just after the Rig finishes it's Transmit. It's a Yaesu FT857D - Worked fine on my old Windows XP notebook. Now its Win 10 on a HP Elitebook Using a Prolific USB to Serial Interface for the CAT which Win 10 sets up with no problems |
|
|
|
Locked
Hamlib error
#WSJTX_config
zs6bv@...
Rig Control Error
Do uou want to reconfigure the radio interface? Detail: Hamlib error: Command rejected by the rig while setting frequency No problem on receive. Error occurs as soon as the software triggers the PTT. |
|
|
|
Locked
Constand Rig Control Error
Gary Shirk
Hi, I have a problem that I really need some help with. I bought a new 15" Dell laptop computer. I just downloaded the latest version of WSJT-X software (2.1.2) and everything was going well. So I thought. But when I try to use the program to transmit, this error message keeps popping up and nothing happens. Error message states: "Rig Control Error - Do you want to reconfigure the radio interface?" No matter what I try at this point, the program closes and deletes all of the settings just about every time. Why is it doing this? I'm using a SiganLink digital interface control box and an old Yaesu - FT-847 transceiver. I was using this same system with an 15 inch HP laptop and the setup worked great. I'm also using the data input connection on the back to switch bands on the transceiver when I switch bands on my laptop. Oh, both were using Windows 10. I would appreciate some help on how to get back on the air running FT8 again. My rig is receiving FT8 signals like it should. Thanks. Gary Shirk April 16, 2020 Call signs: T88SS & KE1AT 73.. |
|
|
|
Locked
Re: K3S and WSJT-X on 160M
Under the WSJT-X Configuration menu, you can create a new configuration. Several in fact. I have the DEFAULT and one named JA-160 which sets the radio to do as described, and one for my Tentec Eagle. I just choose the one I need from the configuration menu and the radio and computer are happy. No need to reset anything. Once and done.
73 Bob, K4TAX |
|
|
|
Locked
Re: Microphone going to sleep?
Mack Edmonson
I think you will find power management in DEVICE MANAGER< USB CONTROLLERS, un tick the “ Allow the computer to turn off this device to save power” Do this for each device under USB controllers. Good Luck Mack, W4ENN
Sent from Mail for Windows 10
From: Dennis Jacobson
Sent: Thursday, April 16, 2020 1:55 PM To: WSJTX@groups.io Subject: [WSJTX] Microphone going to sleep? #wsjtx
Hello again all.
|
|
|
|
Locked
Re: Microphone going to sleep?
Dennis, I see the same thing, but not on a regular basis. Thought it had to do with the computer or screen saver going to sleep, but it's not consistent. I chalked it up to perhaps the computer doing some background operations while idle, but really have no idea. I haven't used "caffeine" in a while to keep things awake, but will give it another try.
https://www.zhornsoftware.co.uk/caffeine/
On April 16, 2020 at 2:55 PM Dennis Jacobson <n6ng@...> wrote: |
|
|
|
Locked
Re: Microphone going to sleep?
Jim Bacher - WB8VSU
When you checked the USB power settings, did you check the HUB its plugged in to as well?
toggle quoted message
Show quoted text
Jim Bacher, WB8VSU wb8vsu@... https://trc.guru
|
|
|
|
Locked
Microphone going to sleep?
Hello again all.
Anyone else having this problem? Everything works just fine as long as I keep using WSJT-X every 30 minutes or so. But should I leave for and hour or more and come back, the microphone no longer transmits the tone.. WSJT-X still keys the radio ok but nothing is generated or sent out on the transmit audio line.. If I restart WSJT-X everything comes back and works fine until I leave for an hour or so again. I've check the power saving option in the device manager in both the microphone and in the USB and none show any power saving options set... I'm at a loss for what else to check. I've always been able to get answers to my other problems from the many people that read this group so maybe I can get one for this problem... Any ideas? Thanks all. Dennis N6NG |
|
|
|
Locked
Re: K3S and WSJT-X on 160M
Tried this briefly last night and seems to work.
toggle quoted message
Show quoted text
Added for 160 meters FT8 another frequency of 1.908.000 in frequency chart, set K3 to Split, and WSJTX to NONE. Transmit on 1840.000 and receive on 1908.000. Everything remained OK after a test transmission. Just remember to change settings when you’re finished trying to work JA on 160 FT8. Hopefully this will be a moot point when and if Japan changes their frequency allocations. Then just delete the 1908 addition. 73, Art., N2KA.. On Apr 15, 2020, at 4:56 PM, Arthur Bernstein via groups.io <n2ka@...> wrote: |
|
|