locked
Re: Worked Before Not Shown
David Kaplan
Are you talking about the stations worked before that WSJT-X gives you? 73, David, WA1OUI
On Apr 20, 2020, at 5:56 AM, Dave Garber <ve3wej@...> wrote: I remember, do NOT run any as administrator. the apps may be blocked from access correctly. try each as not, and try again. also did you rescan your log after doing that Dave Garber VE3WEJ / VE3IE Stations worked before are not indicated. I recently switched computers from a laptop (Win10 Home) to a desktop (Win10 Pro). Everything worked on the laptop. For the desktop, I did a clean install of the OS, WSJT-x, JT-Alert, and ACLog using the latest versions. I used the settings on the new computer match those on the laptop. ACLog TCP settings are enabled, JT Alert/ACLog is enabled and WSJT UDP settings match. I also made sure all applications are run as administrator. I use the internal Elecraft soundcard (USB) and Win4K3. |
|
locked
Re: Worked Before Not Shown
Dave Garber <ve3wej@...>
I remember, do NOT run any as administrator. the apps may be blocked from access correctly. try each as not, and try again. also did you rescan your log after doing that Dave Garber VE3WEJ / VE3IE Stations worked before are not indicated. I recently switched computers from a laptop (Win10 Home) to a desktop (Win10 Pro). Everything worked on the laptop. For the desktop, I did a clean install of the OS, WSJT-x, JT-Alert, and ACLog using the latest versions. I used the settings on the new computer match those on the laptop. ACLog TCP settings are enabled, JT Alert/ACLog is enabled and WSJT UDP settings match. I also made sure all applications are run as administrator. I use the internal Elecraft soundcard (USB) and Win4K3. |
|
locked
Re: Logbook and Computer Crash
On 20/04/2020 03:42, Steve R via groups.io wrote:
Dave,Hi Steve, no manipulation of your ADIF log file should be required, the format is flexible with unused fields ignored and the order of fields in each record is irrelevant. 73 Bill G4WJS. |
|
locked
Re: Receive reports??
On 20/04/2020 03:02, vk4aac@... wrote:
Hi all,Hi Rob, a quiet rural area could easily have a 10 dB lower noise floor than that suffered by many stations. 73 Bill G4WJS. |
|
locked
Re: Set up V2.2-1
Hi,
Are you able to change the port Name as well, i.e. to rename to IC7300 and the other port to IC9700?
Ta
From: WSJTX@groups.io <WSJTX@groups.io> On Behalf Of Wilt Barnum
Sent: Monday, April 20, 2020 02:06 AM To: WSJTX@groups.io Subject: Re: [WSJTX] Set up V2.2-1
Thanks Terry I didn't know that
Sent from my U.S.Cellular© Smartphone
-------- Original message -------- From: terry mckinley <tmk@...> Date: 4/19/20 3:35 AM (GMT-05:00) To: WSJTX@groups.io Subject: Re: [WSJTX] Set up V2.2-1
go into device manager ports and right click then properties then advanced and you can change its number. |
|
locked
Re: Receive reports??
Hi Rob, It will be a combination of both the difference between stations' TX ability, ie the other station is running more power, has a better aerial, etc and the RX ability, lower noise floor. After all the report is a signal-to-noise ratio. 73 Phil GM3ZZA Stay safe. On 20 Apr 2020 03:02, vk4aac@... wrote: Hi all,
--
73 Phil GM3ZZA |
|
locked
Worked Before Not Shown
Howard WX7HS
Stations worked before are not indicated. I recently switched computers from a laptop (Win10 Home) to a desktop (Win10 Pro). Everything worked on the laptop. For the desktop, I did a clean install of the OS, WSJT-x, JT-Alert, and ACLog using the latest versions. I used the settings on the new computer match those on the laptop. ACLog TCP settings are enabled, JT Alert/ACLog is enabled and WSJT UDP settings match. I also made sure all applications are run as administrator. I use the internal Elecraft soundcard (USB) and Win4K3.
Everything works except worked stations are not indicated on WSJT or JT Alert. I am able to log QSOs and upload them to LoTW and ClubLog. When I start up WSJT, the ADIF is scanned and number of stations logged are indicated in the lower left part of the application screen. The number of QSOs logged match what is in my ACLog. I may have missed a setting but I have l have not found the solution to this problem. Any suggestions are much appreciated. Thanks 73 Howard WX7HS |
|
locked
Re: frequency measuring test
Hasan Schiers N0AN
You must have had weak or fading signals when you were frequency hopping. Did you see an asterisks (*) at the end of any line of data you were capturing? Are you using Windows defender for your virus protection? You may need to put your top level wsjt directory in an exclusion with your antivirus settings. I would not advance to saving data with the measure box until you see real clean data from the prior step. Depending on time of day you may have to delete a freq in the FreqCal list, like 2.5 or 5 MHz during high local noon. I've never seen a security alert from accessing the fmt.all file, or On Sun, Apr 19, 2020, 4:59 PM Hasan Schiers N0AN via groups.io <hbasri.schiers6=gmail.com@groups.io> wrote:
for that matter, any file in the wsjtx appdata directory. Sorry for the rotten formatting. Using my tablet in the media room and it put the last part of my reply here at the bottom. 73, N0AN |
|
locked
Re: frequency measuring test
Jamie WW3S
tried this a few times now, every time the file is filled with bad data "*" at the end of almost every reading and the solve for calibration parameters wont run
------ Original Message ------
From: "Hasan Schiers N0AN" <hbasri.schiers6@...>
To: "WSJTX@groups.io Group Moderators" <WSJTX@groups.io>
Sent: 4/19/2020 2:36:22 PM
Subject: Re: [WSJTX] frequency measuring test
|
|
locked
Re: frequency measuring test
Jamie WW3S
never mind....I found what I needed fcal2.out, but boy there is a lot of bad data, * in it....
------ Original Message ------
From: "Hasan Schiers N0AN" <hbasri.schiers6@...>
To: "WSJTX@groups.io Group Moderators" <WSJTX@groups.io>
Sent: 4/19/2020 12:52:04 PM
Subject: Re: [WSJTX] frequency measuring test
|
|
locked
Re: Logbook and Computer Crash
Steve R
Dave, |
|
locked
Receive reports??
vk4aac@...
Hi all,
I have been enjoying FT8 for a few months now, but have a question about my signal reports. 99% of the time the report I receive is about 10db lower than the report I send to the other station. Is this just because of the higher noise level at the other stations QTH, or is it because of my 40w power level or antenna, maybe I'm looking at it the wrong way? I live in a very low noise level area (S1-S3) Just curious Cheers Rob VK2VH |
|
locked
Re: USB Audio Dropouts
Howard Kunkel
I would try checking the event logs in the OS. There could be events (warnings and errors) posted there that may help point to the exact issue causing the problem.
Check event logs under System and Application branches. My 2 cents worth. Hope it proves useful. It can be a great troubleshooting tool.
|
|
locked
Re: frequency measuring test
Hasan Schiers N0AN
You have a setting wrong. 1. You need several frequencies in your frequency table that are specifically labeled for FreqCal. They should include at a minimum: 5.000, 7.850, 10.000 and 15.000 MHz and they should have the label FreqCal on the line that contains the frequency. Once in freqcal mode, you need to : Tools > Execute Frequency Calibration cycle (do not check the check box for "Measure" on the main screen just below the T/R period....yet) Now, if you have the frequencies entered in the Table correctly and you have Execute freq cal cycle as above checked, then: Click on the monitor button to make it green. At this point you should see the frequencies you put in for FreqCal in the Settings > Frequencies table, scroll up the screen, slowly. They will increment more than once in a 15 second cycle, typically, but not always. (They will be offset by 1500 Hz, so 5.000 will show as 4.998500 in the frequency window and so will your radio) In each 15 second cycle you should see the frequency increment or change to the next one in your list. It does not take minutes...it takes seconds. (15). Then it will loop from lowest to highest over and over again. Once you see this behavior you are ready to measure and create your values. Until you see it like this, you have some setting wrong. I have had literally hundreds of people use the steps outlined in what I posted ....if you follow them EXACTLY, they will work. So, if this brief explanation doesn't get you going, please go back and carefully read, then do each step in order, exactly as I listed them. It works...every time. 73, N0AN Hasan On Sun, Apr 19, 2020 at 1:08 PM Jamie WW3S <ww3s@...> wrote:
|
|
locked
Re: frequency measuring test
Jamie WW3S
ok, I have the program cycling thru frequencies now, I hit the stop button, when I go to Solve, it tells me there is bad data in fmt.all, but windows security wont let me open it? I just get a blue screen with windows security at the top header
------ Original Message ------
From: "Hasan Schiers N0AN" <hbasri.schiers6@...>
To: "WSJTX@groups.io Group Moderators" <WSJTX@groups.io>
Sent: 4/19/2020 12:52:04 PM
Subject: Re: [WSJTX] frequency measuring test
|
|
locked
Re: Set up V2.2-1
Dave Garber <ve3wej@...>
also , make sure the comport is not already in use by whatever other software you are running, like a logging software. Dave Garber VE3WEJ / VE3IE On Sun, Apr 19, 2020 at 10:06 AM Wilt Barnum <W1IPL.me@...> wrote:
|
|
locked
Re: Logbook and Computer Crash
Dave Garber <ve3wej@...>
I exported all ft8/ft4/etc files to an adif, then used adif master to confirm it was ok. saved the finished copy into the wsjt local folder, as the required file name. and it helped Dave Garber VE3WEJ / VE3IE I had the joy of having a hard drive failure on my rig computer. I have spent the last two days reloading software and files. I use HRD as my logging program and was wise enough to back up my logs to an external drive. |
|
locked
Logbook and Computer Crash
Steve R
I had the joy of having a hard drive failure on my rig computer. I have spent the last two days reloading software and files. I use HRD as my logging program and was wise enough to back up my logs to an external drive.
As I was reloading WSJTX I discovered that the logfile was gone. I was able to get WSJTX to read my log and it shows stations I have worked before. Is there a way or is it possible to reload the adi file from my HRD log into the WSJTX log file so that the worked before stations will show on WSJTX? I think I could paste the log adi but I know I dont need all the data entries from the ADIF. Can one only the data entries needed for the WSJTX log file? Steve VA3FLF |
|
locked
Loss of Waterfall and Decoding after several minutes operating???
Gary Gadwa
This Issue is driving me crazy. I'm running Signal Link USB and a Yaesu FT-1000MP Mark V. Have both a Dell Win 10 Laptop and a Dell Desktop. Running WSJT-X with the latest version software. I'll be running along making contacts for say 15 minutes and all of a sudden the Waterfall goes blank of signals. and obviously no decoding. Software and Transceiver will still Transmit fine. The waterfall displays a vertical line at 1000 and at 2000 and nothing else. I have tried different cables. Nothing works. Come back a day later and Waterfall and Decoding are back fine. The Audio Codec settings appear fine with no changes to them. I am at a loss!?!?!
GARY W7FSI |
|
locked
Re: frequency measuring test
Jamie WW3S
I do have CAT.....it changed the freq to 2.495 (I Think, it was offset a bit from 2500).....and then it stayed there.....I stopped it after a few minutes, then thought maybe it wants to run longer than that, so I did it again...it stayed on 2.500 for 30 minutes or so, never did switch to 3.300 (next freq in table) ------ Original Message ------
From: "Hasan Schiers N0AN" <hbasri.schiers6@...>
To: "WSJTX@groups.io Group Moderators" <WSJTX@groups.io>
Sent: 4/19/2020 12:52:04 PM
Subject: Re: [WSJTX] frequency measuring test
|
|