I just downloaded and installed the Meinberg NTP Service on Windows 10 and it downloaded, installed, and runs fine. I like that it runs as a service at startup. I still have my USB GPS Dongle so that

UK regulations require 6 character location to be sent (or more loquacious data like 15 km E Edinburgh, EH54 9JE or Livingston) when operating away from home. It just means I shouldn’t use FT8

Correction. It will load on Windows 10 but not Windows 7. -- Thanks 73's de NU4N/Dave

I too thought minpoll of less than 4 was internally rounded up to 4, but I find that minpoll of 3 works (polls every 8 seconds) on my local NTP servers with the version of Meinberg that I'm using.

With a lot of help from this thread, I have established a GPSD/Raspberry Pi server. So far it has much less jitter and delay than the GPS pucks and any time source on the internet. But still if I

Because people will complain if they can’t adjust the output of WSJT-X. But seriously, you need to balance the audio levels, get as high an audio level as you can get to the radio without adding

>If I read the online WSJT help files correctly, the wizards of WSJT indicate that in FT8 Contest Modes, appending the /P suffix will suppress transmission of the 4 character grid locator in the "CQ"

Roger - Regarding use of the callsign suffix /R, the FCC in the USA previously required amateur repeater stations to use the /R suffix if they used a Morse code identifier rather than voice. There

That being the case, then why is the PWR slider in the WSJT-X application available for use in both the TUNE and TRANSMIT mode and why does the application allow for saving those settings? Thus if the

The RSP-1 or RSP-1a SDR receiver connected to your computer with HDSDR or other free software will do the job. You can either terminate the input to the SDR receiver with a 50-ohm resistor or just

Lost split control of IC7300 with 2.5.0-rc3, keep getting hamlib error. Hamlib error: Command rejected by the rig icom.c(1791):icom_set_mode_with_data return(-9) rig.c(4018):rig_set_split_mode

In my experience, the Raspian releases tend to lag software packages like gpsd signficantly. In order to get numbers for "Seen" and "Used" satellites, I had to install gpsd 3.22 When I did apt-get

Dave, Sorry, I don't understand, can you try again? 73, Willie N1JBJ

Re Alan W6AKB write up and random thoughts: Very good job. I have never tried NTPsec as the primary advantage of that version is security enhancements as you say which are really only relevant if you

I tried the program on my windows 10 but will load on windows 7 but keep getting the same error. -- Thanks 73's de NU4N/Dave

ALC indication is not an indicate of ALC threshold or action. In the Elecraft K3, K4 ALC action atarts beyond 4 bars. In most Icoms, powers setting sets ALC threshold, so at 100% there is no ALC

Willie, I use an TS-2000X as my primary rig for FT8 with a RIGblaster Advantage, but� I have used the same procedure on an Icom IC-781 with a Signalink with excellent results.

I don't operate mobile or portable but I have operated from other addresses using WSJTX. I just log into the licencing portal run by the UK licencing authority and change my address for the duration.

So when I’ve operated in a foreign country - say Italy - with proper reciprocal paperwork - my call was IZ0/W6CZ. Sounds like my grid would be dropped and it would be a “non-standard” call? --

This will help.... de Mike W9MDB On Saturday, July 24, 2021, 07:52:41 AM CDT, Jim Johnson KC4HW <jim@...> wrote: