I made several RU contacts today with decode set to Fast and not one crash! Thanks John Gieringer KL7NW

See this document: http://kb6ibb-15.ham-radio-op.net/Ham-Radio/FT-991%20setup%20for%20digital%20modes%20(with%20only%20a%20USB%20cable)%20%e2%80%93%20N1AV%20(xN1RWY)%20on%20the%20air.pdf

Mine crashed 5 times in the first 4 hours of operating. I changed Decode to FAST and did not have a problem for the rest of the contest. Made 245 Q's Thanks for the tip. Bill, AA4R

While participating the the RTTY Roundup today, WSJT-X version 2.2.2 running on Windows version 10.0.19041.685 crashed 17 times. It happened every time on receive and most of the time when I'd clicked

Hi Daniel I was having the same issue it would transmit then in the middle of the contact it would stop triggered. had no output I thought was my radio or signalink.I was not that but the USB

This is interesting. I was part of the early FST4/W test group but I never realized this ramped amplitude was happening. In general I would say it is not good news with class D and E amplifiers which

Hello Peter, I've checked the audio waveform out of the Intel NUC PC and the FST4W-120 start is indeed much slower to rise (~140mS) in comparison with WSPR. In the shots below I've altered the

yup thats the ebay to do it! Dan KC2STA -- Dan Ziolkowski KC2STA SKCC #4290T Ubuntu LINUX

Hi Bart Since I run an FT-991a here, thought I'd share what I set my rig & computer to. Yes, I'm using the default of 50 for the (73) Data Level Out.

Burt, your FTdx3000 USB audio codec *is* a second sound card. Make sure your system default sound devices are not assigned to your rig's USB audio codec and it should all work

My Dell 8940, Windows 10, desktop drives my Yaesu FTdx-300, into my SteppIR vertical antenna. I am using the USB CODEC driver thru the USB port. Everything works! My problem is, if I want to hear

I have been having an issue with wsjtx and signalink, The problem is when I change bands I am no longer have power output. Signalink is triggering my transmit ok. To fix the problem id have to turn

NO LUCK at those suggested frequencies, so I'd been using the program default frequencies all day yesterday - mostly on 20m/40m FT4. Propagation for the other three bands were nonexistent for me

I noticed that in addition to switching to LSB, AGC was also turning on during transmit. I found the "fix" to my issue. Going to "Settings" in WSJT-X, then selecting the "Radio" tab, in the section

Hamish: What do you have for menu 73-Data Level Out? The default is 50. If I use that ALC goes bananas (that's American for crazy high). Some other users set it to 20. I thought I had everything

Hi Bob. Did you read the email contents please as I found your response a bit unhelpful! The operator states she is aware of propagation issues. But asks will these effect ‘audio levels’ or is

You can customize your Alerts on the Alerts Tab under the Settings (all except Counties), and chose which ones you want. Turing on Audio Alerts under Settings>Call Roster will sound "New Hit" for

My 2 cents worth . . . What software are you using for rig control. For example, I use Ham Radio Deluxe with my Yaesu FTdx3000. (But, of course, HRD does not support the Xiegu.) The first place I

Any luck with these frequencies? II just did 5 QSOs at the default frequencies and didn't found anyone at the other frequencies.

Hi Pat, WSJT-X supports transverters by allowing the IF rig offset for a target band to be set in "Settings->Frequencies->Station Information". I don't understand why you would have any issue with