Better yet, just bond each piece of equipment to the station power supply ground terminal. Don't bother with big flexible ground straps or a copper buss bar across the back of the desk. Make some

You could check for RF issues by turning the transmitter power down to zero and/or using a dummy load, so that everything is identical except the RF power. Chris VE3NRT

If you have a SignaLink have you set it to 0dB ins sound control panel for both playback and record? I happen to have a DR80 on the way and I can compare when I get it. Mike W9MDB

That is RF in the shack.  Only happens when you transmit. The CAT PTT test does not generate any power so that's why it works. #1 Type 31 Chokes on the USB cable (both

Is anyone using any of the Masters Communication DRA series interfaces. What success and was it an improvement? Tom, WA9AFM

Hamlib error: IO error port_open: serial_open(COM3) status=-6, err=Input/output error iofunc.c(81):port_open return(-6) rig.c(800):rig_open return(-6) while opening connection to rig I have rebooted

Dave Years ago I did use JT9 a lot. It was better then JT65 but less popular. In time FT8 became very popular and did replace all other modes. What do you mean by JT9G(Fast)? Why? Auto Sequencing

I have the same issue with new install. Something is not right.

I am very interested in this, because I have a 16" MacBook Pro, on order. Try all the stuff that appears in the drop down box. One of them should work. If not go look for a different driver. Curiosity

That worked! Piece of cake! Tried downloading it in Firefox - it balked at me. Safari allowed me to download. Thank you very much Buddy WB4OMG

Hi Dave, Perhaps this extract from User Guide explains a bit: 7.3. Auto-Sequencing The T/R cycles of many WSJT-X modes allow only a few seconds to inspect decoded messages and decide how to reply.

Try this again and hopefully formats correct this time New hamlib for Windows installation directions #1 Shut down WSJTX #2 Download either the 32-bit or 64-bit DLL -- hopefully your browser

Please download the latest hamlib and see if it fixes the problem. New hamlib for Windows installation directions#1 Shut down WSJTX#2 Download either the 32-bit or 64-bit DLL -- hopefully your

I was using 2.5.0, under Windows 11. Everything was fine with all three of my radios - IC 9700, FTDX 101, IC 705. Upgraded to 2.5.3. The FTDX 101 works just as before. The IC 705 works as before. But,

I have a new MacBook with the M1 chip. Latest version of WSJT-X loads and shows AUDIO CODEC in the AUDIO tab. However, I cannot find the /dev/cu.SLAB_USBtoUART portin the serial port box on the RADIO

I do MSK144 meteor scatter on 6m and 2m and have always been interested in trying it on 10/12/15, mainly due to N0AN's past posts on the subject. This morning, I tried using JT9G(fast) with a friend

Jim, Yes, you are correct! When I looked before, I just looked at the tags and branches, and only saw up to 2.5.2, however if I look at the source itself, it is indeed 2.5.3. 73, -Joe- K0OG

Please let me know how it goes with the test, again sorry about my error. 73. CUL. Mack

Hi Mack yes my maximum drift is set to 0. Will try tomorrow and see how it goes with the F TOL on 20. Unfortunately there were no multiple stations on this morning to test it cheers Wayne VK4WTN

Wayne, I have made a mistalke about my settings, my F tol is at 20 and has never been changed. It is the Max drift setting that I keep at 0 . If i change the Max drift to anything other than zero I am