I used WSJT-X v2.4.x with Quisk v4.1.93 and it worked well with Hamlib NET rigctl localhost:4532 and Virtual Audio Cable (line 1). I upgraded WSJT-X to v2.5.3 and it does not anymore work with these

Ruth Sorry I forgot to mention in the WSJT-X Settings Audio tab Soundcard set both the Input and output to Mono. 73 Rick GM4JIB

Hi Ruth I run WSJT-X 2.5.2 on a laptop running Linux Mint 20.1 with a signaLink.  As Dan said pavuctrl is the way to go.  It just sits on top of alsa so you don't need to uninstall

The tarball for wsjtx-2.5.3 is available now on the wsjtx web site. Chet Sent from my Verizon, Samsung Galaxy smartphone Get Outlook for

Ruth audio is either not getting to the signalink, or levels are too low. have you tried to adjust tx level on front of signalink. make sure delay is off. do you have pavucontrol? it is a visual of

Would it be possible to have the little 'tick mark' on the Pwr vertical slide bar a bit bigger? The way it has been "since way back when" is so tiny the only way I can find where it is is by trial

I've been successfully running WSJT-X for my TS-480SAT on my Mac (Mojave) with a SignaLink. I've been trying to set it up on the Linux laptop I don't use a ton to free up the Mac. The laptop is

Hello Jeff, Try disabling the Burr Brown device in Pulseaudio. You can do this using the pavucontrol utility from the shell command-line. After that, restart WSJT-X. If Pulseaudio acquires the

Hi Alan, thanks for the reply. Ah, that explains it - nice to know that it is not a problem with my laptop at least, although not so nice that it is likely not a fixable problem (unless there is some

Please place the attached file in C:\Users\[username]\AppData\Local\WSJT-X Restart WSJT-X and duplicate the problem.Shut down WSJT-X Then send me the WSJT-X_RigControl.log file that will be in the

PTT does not release on yaesu 450D when using WSJT-X.

Andy, Technically, the Racal 6790GM is "untested" with the latest versions of hamlib. 11003 Racal RA6790/GM 20200113.0 Untested RIG_MODEL_RA6790 You may want to

This seems to be a Kiwi SDR characteristic. It has its own built-in WSPR decoders that work with little DT. I run Meinberg, and 5 or more instances of WSJT-X which keep good time. Some use VAC for the

If possible substitute a second PC or laptop running the same version of WSJTX and isolate the issue. A long-shot but most all modern PC’s still have a CMOS battery for the RTC. Faulty RTC or

Roger, I did exactly that some time ago with similar results. As far as I remember it maintained the ~4 seconds DT for many hours. I think it eventually got to the stage that lots of spots were

Hi Roger, I assume that you have disabled Windows time service as Meinberg stays butt. You could use some other timekeeping that is stable enough and listen to audio directly from rig, if that is

Hello Gwen, I've been using my 7300 with wsjtx for years without this problem. I don't know of any setting within the 7300 that would cause it to stop listing the Burr Brown TI AUDIO CODEC as an

My Racal 6790/GM has been experiencing Cat rig control errors with WSJT-X for some time. While this specifically references WSJT-X 2.5.3, this error goes back to at least version 2.5.0 and seems to

Then change the time for reporting up to 10. Can remember screen. So if you need. I can check when jn the shack sent via LG hand held device

OK, have placed the file in the same directory and will await results! Thanks Michael.