main@WSJTX.groups.io

Re: Trouble with Yaesu FT-747GX CAT #windows11 #Cat_RigControl #hamlib

I confirm the error exactly as described. when it must read 7.000 MHz it reads 7,000 MHz and that makes it impossible to use it. Keeps happening since more than a year in all wsjtx versions until the

By Mauricio A. Taslik · #37396 ·

Re: WSJT-X + Icom Ic 9700 #WSJTX_config #Icom

By non-trivial answers I meant things like "did you check the right COM port?" In any case, these are the CI-V settings for both of my IC-9700s. I remember that one works perfectly with WSJT-X

By Fabrizio · #37395 ·

Re: Trouble with Yaesu FT-747GX CAT #windows11 #Cat_RigControl #hamlib

Please try this DLL....I just made a change that should help this.... https://www.dropbox.com/s/7aejdv74nfjxr0q/libhamlib-4.dll?dl=0 And if it still is wrong (which it likely will be) please provide

By Mike Black · #37394 ·

Re: WSJT-X + Icom Ic 9700 #WSJTX_config #Icom

Without knowing what settings you have already set, it's difficult to know what is "nontrivial" and you suggest you've tried everything already, so again, it's difficult to help without appearing to

By David Ackrill · #37393 ·

Re: Trouble with Yaesu FT-747GX CAT #windows11 #Cat_RigControl #hamlib

FT-747GX is fixed at 4800,N,8,2 ... there is no option to change any of that. 73, ... Joe, W4TV

By Joe Subich, W4TV · #37392 ·

hearing voice on FT8 #FT8 #txaudio

for what it's worth; I saw an earlier post about hearing voices on FT8: I had the same issue. i was also using grid tracker I turned off voice with alerts and it went away. so I would try that if

By Chuck Maletich · #37391 ·

Re: WSJT-X + Icom Ic 9700 #WSJTX_config #Icom

Yes I have. I sum up the situation: 3 radios: IC-7300 IC-9700 "Local" IC-9700 "QO-100" all connected with the same pc IC-7300 and IC-9700 "local" matched with WSJT-X Ic-9700 "QO-100" not. I compared

By Fabrizio · #37390 ·

Re: FT8 Intermittent no signal on transmit #transmit

I think a few have reported an issue, but am not aware of (nor have I seen) any change in that area . .. -- Sent from my Android device with K-9 Mail. Please excuse my brevity.

By Tim Dawson · #37389 ·

Re: WSJT-X + Icom Ic 9700 #WSJTX_config #Icom

Do you have separate configurations in WSJTX for the 7300 and 9700? I have the same two rigs working well with WSJTX this way. Dennis, N1RDN

By Dennis · #37388 ·

Re: FT8 Intermittent no signal on transmit #transmit

I thought that, in the latest versions, the power slider isn't connected anymore?

By David Ackrill · #37386 ·

Re: Trouble with Yaesu FT-747GX CAT #windows11 #Cat_RigControl #hamlib

A couple of quick things to try...Try using 1 stop bit. Failing that, try a slower baud rate. 73, Dave - N5DCH

By David Herring · #37385 ·

Re: FT8 Intermittent no signal on transmit #transmit

Proper ALC level depends on the rig. Some want zero...some want a bit of ALC in order to get maximum (not full) power. You have to know your ALC's behavior. One way to tell is pretty easy. Set

By Mike Black · #37384 ·

Re: FT8 Intermittent no signal on transmit #transmit

Occasionally (once every few dozen tries, perhaps?) after I use Halt TX to stop an unwanted transmission, the next time a message is transmitted there will be no audio; the rig is switched into TX,

By ve3ki · #37383 ·

Re: FT8 Intermittent no signal on transmit #transmit

I've had this issue for a couple of years now. I think it is a known bug. It has happened with each update of the program here. The solution? Quickly hit Halt TX, then Enable TX. 99% of the time this

By David AD4TJ · #37382 ·

Re: FT8 Intermittent no signal on transmit #transmit

If you are running with ALC showing then you could be over driving your audio anyway.

By David Ackrill · #37381 ·

Re: FT8 Intermittent no signal on transmit #transmit

Hi Bob, nope. I occurs using WSJT-X and watching my monitor. Saving is switched of on my monitor. 73 Alex

By alex · #37380 ·

Re: FT8 Intermittent no signal on transmit #transmit

Hi, It could be you have an HDMI monitor and this can cause this problem. There are several threads on this on the forum. If you think this may apply to your set up, change settings to stop the

By Bob G8HGN · #37379 ·

Trouble with Yaesu FT-747GX CAT #windows11 #Cat_RigControl #hamlib

I'm trying to setup CAT to control my rig; my settings are: COM4 8 data bits 2 stop bits no handshake other pins on default The Test CAT button works, it sets to green, and PTT also correctly starts

By kedrot@... · #37378 ·

Re: Max waterfall frequency, and merging log files. #TechnicalHelpQuestion

Thanks to everyone. All is in order again. I rely on Gridtracker for my stats and it lost track of most of my states. Reinstalling it found everything. GT must maintain it's own DBs for stats.

By Barry Bogart · #37377 ·

Re: Kenwood TS440s/Signalink USB combo ALC vs PWR vs SWR issue #signalink #Kenwood #FT8

Hi Joe, The 440's ATU is only good to about an SWR of 2:1. I have a Yaesu FC301 manual tuner with an 80-10m Off Center Fed Dipole, and works great. Good up to 300W. They aren't made anymore, but

By JP Tucson, AZ · #37376 ·

Messages