Please explain W4DNR

For the last few release versions and the rc's, I've had 2 and sometimes 3 stations on exactly the same offset or so very near, and all decoded, however there may have been even more. This happens

IC7610 v1.30 - SignaLink - HRD v6.8.0.340 - JTAlert v2.60.0 - GridTracker v1.22.0725 Also use: Win4ICOM v1.390-x64 for USB sharing and other features WSJTx multicast for UDP -- 73's George -

I was never aware of any 50hz boundary and I have ten of thousands of ft8 contacts in the log. There is a slightly better chance of copying two stations if they are off by a few hz rather than

The 50Hz boundary is a complete myth.  FT8/Ft4 will be happy anywhere in the audio pass-band. Larry / W1DYJ

I always click on a 50Hz boundary before transmiting and most other operators do too. If this is the convention, I wonder why WSJT-X doesn't, by default, override us to do that. Lately, I've noticed

Thanks to all for the suggestions which along with Kenwood's PDF, https://www.kenwood.com/i/products/info/amateur/ts_590g/pdf/ts590_g_ft8_settings_en.pdf, got me back up and running.

If you are doing an UPDATE from the repositories (vs a new/fresh install), it should leave legacy programs alone and allow you to continue as things stood in FOCAL Gwen KI5PXQ

I’m also using 706 and assuming you have baud set correctly and can connect to WSJTX, make sure VOX mode and your audio drivers (in/out) are defined correctly. On the rig itself yeah 20m/USB, set

Are you connecting the 7610 to the new PC(s) using the 7610's USB port? If you are, have you installed the drivers for the 7610 on the new PC(s)? If you haven't installed the drivers then you'll

I had a similar issue and "sort of fixed it " by following the troubleshooting steps for the microphone audio to the point where the automatic system asks to reinstall the audio drivers. After

I have a newbie to linux question. If I update from 20.04 ubuntu to 22.04 would I need to reinstall apps like wsjt-x? I am currently running 2.5.4 and would like to continue with it since there

Gary: I recently got Winlink, flDigi, and WSJT-X going on my old 'Mk2G using the ubiquitous Signalink and the CI-V cable. The Signalink attaches to the 13-pin connector on the back and then USB back

Awesome, Thank you both! ...Gary, KB7QWC

I had rc1, rc2 and rc3 without any crash. But it's true, to revert to 2.4 is impossible without cleaning the system manually... it's a bug, in my mind. Pietro I2OIM Il giorno gio 25 ago 2022 alle

Tnx George. Radio and logger please. -- 73 Ron  W3RJW FTdx-5000, Timewave Navigator, WSJT-X Improved 2.6.0 rc1, JTAlert 2.60.0, HRD Deluxe v6.8.0.338 FTdx-3000, SignaLink USB

Also, if you have an SSB filter installed, make sure it is OFF, so you'll have the maximum bandwidth possible for digital contacts. David AD4TJ

With rc2 initially, I had the occasional crash, unlike any previous version I can remember. It did not appear immediately but apparently started after a Windows update. Perhaps a following Windows

Hi Ron. The radio is an Elecraft K3 (just one -- not SO2R) and the logging software is Logger32. Both have worked very smoothly since 2019 under 2.5.4 and its predecessors and there has been no

Which version (2.5.4 or 2.6.0 rc3) is recommended for the WW Digi Contest this weekend? Thanks, - John, N0TA