Gee. Every 60 hertz. Let me guess... AC hum! Ground loop? 73 de George, KD0RII On 2019-07-06 14:16, W7DDE wrote:

That is a Chinese over-the-horizon radar that has been giving hams fits for a while now. Ron W7HD On 7/6/19 12:16 PM, W7DDE wrote: -- Ron W7HD - NAQCC#7587 OMISS#9898

2019-07-06 at 19:10 UTC 40 meters is showing the pattern attached. Is this my rig or something else. All other frequencies are displaying fine. W7DDE

Joe, I stumbled across a working situation when I used a different computer. The WSJT-X problem went away and all works fine. However, the computer is an old one that I use as a test bench and I would

I only use PKT-U to transmit. and that does not work. As you suggested I took HRD out of the loop and sent you the settings for WSJT-X It still does not work. 73 Roger ZF1RC

If you are using DK II, the FTdx5000 (or any other Yaesu transceiver) *MUST ABSOLUTELY USE PKT-U MODE FOR TRANSMIT*. The transmit audio out from DXK II connects *ONLY* to the PKT or DATA jack and

Joe, I did as you suggested and can decode FT8 and can key the rig but there is no audio or power output. Attached is a screen shot of the WSJT-X settings to be checked in case I have messed up

Hi guys- For 10m, I see the current default channel is 28.18 MHz.. With international beacons down to around 28.160 MHz and lower (Region 2 bcns from 28.2-28.3 MHz), I think a more suitable channel

Roger, Why don't you (temporarily) remove HRD from the equation? Close/unload HRD and DM780, configure WSJT-X to access the CAT and PTT ports *directly* (see the example configuration for DK II and

Joe, I checked all the settings you suggested but unfortunately there is still no power out on transmit and only a steady carrier. If you would like I can give you access by TeamViewer or I can pass

It's the results of reading in wsjtx_log.adi with all the QSOs in it. de Mike W9MDB On Friday, July 5, 2019,

I see this if I go to Settings - Colors and click Rescan. Not on startup though. Mike G7TWC

On the bottom left of the WSJT-X screen a message appears for a few seconds before it is covered by the yellow Receiving rectangle. "Scanned ADIF log, 61 worked before records created" without the

Scott, There is some activity on 14.080 MHz, both on PSK Reporter and on my waterfall, but I’ve been unable to decode them. But then my current antenna is 6 dB above a dummy load on that

The TX Soundcard settings *have nothing to do with waterfall and decode* If the sound comes out of the computer speakers, WSJT-X is configured to use the wrong sound card for transmit. With DigiKeyer

My Icom IC-7300 works fine for FT8 etc which shows I can setup the software. The FTdx5000 relies on the Digikeyer II and while that interface works with other makes of radio it does not work with the

See: https://groups.io/g/FTdx-5000/topic/ft8_should_run_in_usb_not/27807657?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,0,27807657 SeventyThree(s).

The radio is set to PKT-U for WSJT-X The radio is set to RTTY for rtty The constant tone is not a result of the radio being set to anything other than PKT-U when I transmit from WSJT-X There is no

The radio is set to PKT-U for WSJT-X The radio is set to RTTY for rtty The constant tone is not a result of the radio being set to anything other than PKT-U when I transmit from WSJT-X There

What mode are you using in the FTdx5000 for RTTY? What mode are you using in the FTdx5000 for WSJT-X? DigiKeyer II supplies audio to the PKT jack - you *MUST* use PKT-U to transmit as that is the