My set up\ Surface pro, signaLink USB, ICOM 746 using mike input - program decodes messages, can double click to respond to CQs but does not auto sequence the rest of messages, box checked for auto

Good morning, all - It's been a couple of years since I last used WSJT-X (life got in the way. . .). Trying to get things put back into operation, and find that I cannot get the RX audio display to go

Microsoft did the same thing to Windows 10 users a few months back. It's generally not a good idea for Apple to mimic them so closely! Karl Beckman -- Karl  WA8NVW  OH WA8NVW@... in

I use a MacBook Pro with an FTDX10 so cabling will be different but once connected for the audio you’ll need to go into the Audio MIDI settings and make sure the codecs show up under audio devices

I have the opposite view.    Many times I've heard sounds other than WSJT-X tones transmitted due to using an 'air gap' type of system.    People's conversations, TV audio, and so on.   Some,

I work ft4 on a couple of the LEO's here. I use two copies of WSJT-X to work the sats fullduplex. For logging I use JTAlert along with DXLab and SatPC32 to auto log the sat contact info. Are you

Tom I really like your answer of using speaker to microphone for getting basic decode capabilities. I find that simple solutions like this, although not always optimal, can provide tremendous

Hi David; Since you are just getting started, all you need to receive & decode WSJT-X signals, besides what you already have, is a quiet room. You can then receive & decode WSJT-X without any cable at

Hi Karl, I enhanced WSJT-X so that it logs SAT name along with the RX frequency which it didn't do before. Just looking for beta testers for my patch. vy73 de Florian DF2ET

Is it really useful? Why adopt FT8 on QO-100, where the s / n ratio is not so low as to justify it? I could understand a request for LEO, but a much less Doppler sensitive modulation is needed in this

Hallo Florian ! I didn't understand what you want to Test. I am on QO-100 and a test is possible. How can I help you ??? Karl OE3JAG Am 29.01.22, 14:22 schrieb "Florian Wolters (DF2ET)"

Dear group, I saw that (full) support for SAT mode QSOs was requested several times. Im implemented a patch for that and tried to post it to the list but apparently this got denied. So if anyone

Hi - I have an ICOM 746 and signaLink USB; using front mike jack, using surface pro as computer - decoding fine autosequence not working - any suggestions? N3INM

Don’t cross the streams. ________________________________ Sent: Friday, January 28, 2022 5:27:40 PM To: main@WSJTX.groups.io <main@WSJTX.groups.io> Subject: Re: [WSJTX] Aggregation of two RX Streams

Hi, The Split operation in the Radio tab has nothing to do with the radio frequency split operation. It is very useful to keep your transmit signal clean. The radio frequency split is indicated by

Best place is where nobody else is lurking.If you are calling CQ or calling somebody else your transmit should be in a clear spot -- no other requirement than that.If you are answering the same rule

What is the correct place to put transmit vs receive cursors ? Relationally. Transmit above or below? And what amount of offset? I imagine the software must have split enabled? Ty qsl

In reality what is needed is a correlation function - where one instance of WSJTX can take input (UDP?) from a second instance and combine/dedupe the two streams. I don't know if the UDP stream

You've hit on the problems. As an EE, a ham for 65 years who uses diversity a lot on CW with my K3, and a retired audio professional, I consider it a very bad idea to combine audio from two receivers

I’m 80 years old and have little computer knowledge but willing to stretch my mind a bit and learn. I’ve downloaded the WSJTX app and have it ready to go. What do I need to know to connect my