main@WSJTX.groups.io

See +++ below Sent from Mail for Windows 10

By Philip Rose · #6176 ·

Re: Help setting up rig control for ANAN-8000DLE and WSJT-X

See +++ Sent from Mail for Windows 10

By Philip Rose · #6175 ·

Lee, As Bill says, if you turn off CAT control in Rumlog, and all is set correctly, when you complete an FT8 contact and save it, the frequency and details of the contact will be sent to Rumlog. I

By Dave - VA3CP · #6174 ·

Icom 9700 and Icom 7300

I have both the IC-7300 and IC-9700 working with MacLoggerDX and WSJT-X. The odd thing is I have to unplug the IC-7300 USB cable in order to route audio to and from the IC-9700. Switching audio

By Steve · #6173 ·

Re: Power fluctuates during transmit

William, If you are not using Split Operation under the radio tab (fake it or rig) and are close to the rigs filter edges this will happen. You need to stay between 500-2500 on the waterfall in this

By N2XK Fred · #6172 ·

Re: Power fluctuates during transmit

I reboot my old laptop when that happens. I hear a set of clicks when listening to my signal. Happens after 4-5 hours of the app running regardless if the radio is on or not.

By Jerry AA2T · #6171 ·

2.1.2 vs Buster

Has anyone been able to install wsjtx_2.1.2_amd64.deb on Debian Buster? If so, where did you find libgfortran3?

By Rick Hatton · #6169 ·

Re: FW: WSJT lock ups

Gents, Many thanks for your kind replies regarding this problem. I think Marion K4GOK may have the solution. I must confess I had not considered the Norton security software suite but that

By Francis Thompson <icongeo@...> · #6168 ·

Re: Power fluctuates during transmit

Might be worth double checking that you still have the right audio device selected in WSJT-X settings.

By 4X1ST Tim · #6167 ·

Help setting up rig control for ANAN-8000DLE and WSJT-X

I have an ANAN-8000DLE and presently have WSJT-X and FLDIGI set up to work without rig control and I use one program at a time so I am using the same virtual audio cables pairs for both programs and

By Bcolberg@... · #6166 ·

Re: WSJT & RumLogNG Settings

Bill, With use of my Apple MacBook Pro, you stated that I only have use of one serial port. Could I use either a USB switch or hub, thus increasing the shared potential for both WSJT & RumLogNG to

By Lee Broestl · #6165 ·

Re: FW: WSJT lock ups

I went to the Control Panel and hit the Programs and Features icon and uninstalled everything listed that Del in the name. I don't recall the names, but I think they all had something to do with Dell

By Joe · #6164 ·

Re: sizing of WSJT-x window

Jay, By waterfall not being sized horizontally do you mean you cannot extend the right side of the wide graph out to around 3000 KHz? If that's the case, increase your bins/pixel setting to a higher

By Rich - K1HTV · #6163 ·

Re: Power fluctuates during transmit

William, My setup does the same thing sometimes. I have an older, Windows laptop. When it gets bogged down, it can “burp” the audio signal to the radio sometimes. You might want to look at

By Chuck Adams · #6162 ·

Re: WSJT & RumLogNG Settings

Thanks for that Lee, only one application can open the CAT serial port to your rig at a time. The error message is saying the serial port is not available, probably because RumLogNG already has it

By Bill Somerville · #6161 ·

Re: WSPR 2.0 - Call sign (callsign) munged on transmit

Thanks Bill, I mistakenly had left out the / in the call. 73, Casey On 2/5/2020 2:52 PM, Bill Somerville wrote:

By NA7U · #6160 ·

Re: Power fluctuates during transmit

I use my flag pole for my HF antenna. In strong winds, my power fluctuates. :-| Chuck

By Nc8q-mesh@gelm.net <nc8q-mesh@...> · #6159 ·

Re: WSJT & RumLogNG Settings

Bill, Thank you for your note. Guess I was sort of remiss NOT including an error message. I will go one better including a screen shot. This shows both WSJTX & RumLogNG active. The WSJTX frequency

By Lee Broestl · #6158 ·

Re: Power fluctuates during transmit

Check your DC power connection from power supply to radio. This includes powerpoles & fuses. I've had poor connections develop & needed 'cleaning'. Also, I've had a bad fuse socket that showed heat

By Kevin k5vp · #6157 ·

Re: WSJT-X fails to connect to DX Lab Suite Commander

OM, what is the full text of the error message, including the details? For your convenience you can copy the full text of the WSJT-X error message to the Windows clipboard by hitting CTRL+C while the

By Bill Somerville · #6156 ·

Messages