Hi Jerry, Thanks for your help. I plugged in a flash dive, the laptop (LP) gave the audible connection sound, but no COM Ports were showing in the Device Manager. Did the same with IC 7610, got the

If the com ports are hidden in the device manager that means that the device has not been detected. I would suggest: 1. Try a different USB port 2. Try the device on a different

I wonder if you are using N1MM+? I noticed that it was occasionally listing some shorter variations of the call I clicked on. Ie: KF2T# also listing KF2T in the lower part of the entry window. Not

I use CCleaner, one of the widely used computer utilities. Everytime I run it, I get this from the WSJTX program: "c/users/name/AppData/Local/Temp/WSJT-X/wsjtx_status.txt" not working. Is there a way

I wonder if this might not be a JT-Alert problem? Like you, I get alerted by JT-Bridge (I'm on a Mac) when KF2T# calls appear (I'm KF2T), but I don't recall WSJT-X stopping my activity.

I too had trouble after the last Windows update and that was before any upgrade to WSJT-X. I located the hamlib app and reinstalled it. It reported an error during the install which I ignored and

... when i disconnect the 2nd monitor ... there is no differece no start no icon in the taskbar tnx bill

hello Bill, tnx 4 ur answer. yes, i use an 2nd monitor and there are normal the WSJTx-2.1.2 Prgs.. JTAlertX etx. there is NO icon in the taskbar. my best regards Walter OE6IWG

Hi Bill, Ok, what is that supposed to do? What response am I looking for? 73 - John - N7GHZ

John, please do the following and report back what is printed: open a CMD prompt window. Make a note of your COM port number that is your CAT serial interface and

Thanks Bill. I was afraid of that. Maybe they have a work around. 73 N2BBT Bubba Tim Hero of small cats and defender of undersized lobsters www.bubbatim.com

Hi Bubba Tim, if the COM port you have for CAT control does not appear under the "Ports (COM & LPT)" section of Windows Device Manager then you have an operating system issue.

On 12/05/2020 12:51, zs6c.ham@... wrote: Hi Geoff, thanks for the issue report, we'll look into that for the next release. 73 Bill G4WJS.

Hi Walter, it may be starting with the window off the screen, this can happen if you last used WSJT-X with a second monitor and now do not have it. Is there an icon for WSJT-X on the

That most of the issue. COM Ports do not show up in the Device Manager. You can only see them in the "Hidden" files. Bubba Tim Hero of small cats and defender of undersized lobsters www.bubbatim.com

Hi there, this has been occuring on quite a few releases of WSJT-X. At the moment I am using v2.1.2 This is what happens a lot. I am ZS6C and there is also a ZS6CR. When I am calling CQ and ZS6CR is

Hello All, the RC1 does not start when i click the icon. for abouth 5 or 6 seconds i see the "sand-watch" from the cursor, after this is nothing... silence... no error.. nothing but i can see wsjtx

Re:- As for support on hamlib, nobody's home and 'they' haven't made an upgrade in years according to; well, just about everyone. It is semi-orphaned. ~ ~ ~ Well. If you get

I agree Bill, The hamlib team are very active at the moment. They are preparing to release 1.4 shortly, but the mod rate is not really slowing down enough to give them a window – too many new

Hi Does the Windows Device Manager show the adapter when plugged in - tried a different USB port ? Tom -- 73 Tom GM8MJV (IO85)