Hi Bill and Joe output problem solved - shazaam! receive problem remains. new soundcard, unlike my old one, has no "line-out" port. so I connected playback mode to the new card's speakers port. turns

The problem with this method is the ALT character does not render as an actual zero to any software that is looking for numbers. This can cause unexpected problems. Best to use a font that actually

Making comments about 200-300 watts being excessive power primarily indicates that the person has no real experience in weak signal work on either 160 or 6 meters with WSJT-X modes. Before making such

How to make a “Slashed Ø” for your Callsign Mark R. Henry, WAØWIK Awhile back, someone asked me how I generate a “slashed Ø” when typing my call into an e-mail or other document. Some of

Actually no. Take a look at ARRLs review in Jan 09 QST. They showed TX 3rd order at 25 dB which is pretty bad don’t you think. That was probably due to them running the k3 at a lower dc voltage.

Mark, your comment "K3, which doesn't have the best TX intermod performance" using WSJT "degrades my tx purity to the point it affects decoding..." Nope. The K3 TX IMD was the gold standard for

Personally I think that is excessive. More than 50 watts is unnecessary in most cases. If you have to resort to power then do a better job on your antenna system. My antenna is a random wire in my

The "right" power level is STRONGLY dependent on what band, what you're trying to work, how good your antennas are, and how well you can hear. As I stated in a previous post, I run legal limit for

The most likely cause is that RX noise on the other end of the QSO is higher than on your end. This happens to me almost all the time, even when I'm running legal limit on 6M, or for long haul QSOs on

OMG I thought doing 100 watts sometimes was way over doing it. 300 watts wow. I’m glad that you posted that so I have a naïve idea what people are using for power. 73 Darl NA8W

I found the same thing here on 6M. With 75W out I was fairly consistently 6dB weaker than the other stations. I increased my power to 300W and that pretty much equals things out. I think that the

+ AA6YQ comments below Hi Robert, OK, that means you probably have to report the issue on the DX Lab Suite support list https://groups.io/g/DXLab. + Robert, please attach the errorlog.txt file from

I seem to always get a worse SN report than I give out, especially on 6M. I run an K3 which doesn’t have the best TX intermod performance and I wonder if that degrades my tx purity to the point it

Make sure you have the screen wide enough to display it after the decode....  GL and VY 73, Lance -- Lance Collister, W7GJ(ex WA3GPL, WA1JXN, WA1JXN/C6A, ZF2OC/ZF8, E51SIX, 3D2LR, 5W0GJ, E6M, TX5K,

An update... Before I got the problem to the workbench I got a security update for the Mac which disabled the USB to Serial driver. Since I would need to reload the driver I went ahead and updated

I have just helped a friend set up WSJT-X and he is having a lot of fun. Two items: We have the proper box....Show DXCC, grid etc checked off but the country name is not displaying, it will show EU,

Are you sure you can connect to your radio direct from Commander? I say that because Commander does not require an XML file as you state, the radio is listed in the pull down on the radio page Dan

Joe; Thank you. You caught me not reading the notes and I am embarrassed. Jim WA3ERQ

Question? Why no network identified? RobertW6INO W6INO ~~~~~~~~~~~~~~~~~~~~~~~~~~~ Twenty years from now, you will be more disappointed by the things you didn't do than by the ones you did do. So,

Hi David, try Consolas font in the general font setting robert W6INO W6INO ~~~~~~~~~~~~~~~~~~~~~~~~~~~ Twenty years from now, you will be more disappointed by the things you didn't do than by the