Hi Rainer I don't know if this'll help you but if I want to loop audio like that on my Linux system I play out to the HDMI port and in your case would then connect the WSJTX audio input to the

Hi Rainer, thanks for the issue report and crash dump file. The crash is deep in some Apple CoreAudio code which is in turn called from a Jack audio library. I doubt it is anything we can address, I

Hi! I wanted to use JackAudio as a virtual audio cable to feed audio directly from one application into wsjtx. Currently running JackOSX 0.91 from here: https://jackaudio.org/downloads/ JackPilot is

OM, are you using the same rig and setup as the OP? 73 Bill G4WJS.

Seen something similar, sitting for awhile, hit enable, ptt goes, no audio. If I cycle halt and back to enable quickly it works. Using win 10 Home 1909. Not a big issue for me. I do find also

Hi Gary, AV products are becoming a serious hindrance for PC users. Seriously, service port 4739 is where spot information is sent to PSKReporter, it is only sent once every 5 minutes so

I did not write down the port or the IP address (it started with a 74. and the port was 4 digit starting with 47XX). Just want to be sure this is normal operation as it was quite unexpected. I of

I have WSJT-X 2.2.0 running on Kubuntu 20.04 I always build from source though. 73 Stan KM4HQE On 6/5/20 3:41 AM, groups@... wrote:

Hi Keith, glad you have that sorted out. You are of course welcome to force the 'en-US' language in WSJT-X, our intention is to make life easy for those whose preferred first

Hello Ryan, Huge thanks for your suggestion, which works fine. Now I can run WSJT-X 2.2.0 with English interfaces. 73 de JH3SIF, Keith

As far as I can tell, FT-991 / FT-991A users are having the same issue. Including myself. Few threads below have 2 or 3 workaround, pick your method. Link below is what I did you get around the

I installed WSJT-X V.2.2.0 general release under Windows 10(64bit) today. But CAT does not work between Yaesu FT-991A and WSJT-X recent version. Error message is illegal parameter when reading

I can confirm that WSJT-X 2.2.0 works well on Kubuntu 18.04.4 LTS as did all the RC versions. Roger GW4HZA I can confirm that WSJT-X 2.2.0 works well on Kubuntu 18.04.4 LTS as did all the RC

Hi again, I have CAT selected. Baud rate is set at 38400 as is the radio. This I have tried all the other options and this one is the least troublesome but still gives the errors as described in the

Current software configuration: WSJT-x v 2.2.0, Flex DAX v 2.6.2.50, Windows 10 Pro v 1909. FlexRadio 6600M transceiver running v 2.6.2.50 software. After WSJT-x in FT8 mode sits in a receive/monitor

I just installed the new version today, and am loving it! Immediately, noticed the improvements to decode performance on my Windows 10 PC (3.0 Ghz Core2Duo 8 Gb ram, SSD). Running search and pounce,

1. Thank you, Bill, for the additional help towards understanding this timing topic. Hopefully, Meinberg will just run fine and I will not have to re-visit this aspect at all.

Hi, Interesting something noted, the “B” VFO doesn’t show this problem. What does this tell you? W6INO ROBERT W6INO ~~~~~~~~~~~~~~~~~~~~~~~~~~~ Twenty years from now, you will be more

With rig fake it' , The Freq. goes 50.313 to 50.312 on wsjt-x but the “a” vfo goes to 51.313 Both VFO’S ARE THE SAME AT 50.313 and USB

A 1 MHz change on 6m. or a 350 kHz change on 10m, seem bizarre - not what you would expect the program to be doing. They make me wonder what is going on with your rig control. A couple of things you