You are wrong. From the Kenwood TS-440 Instruction Manual, pg 32: * IF-232C Interface The IF-232C interface is the adapter for connection between the RS-232C terminal of a personal computer and

working great here as well. Jack VE7DFJ

Don't start here either. Running Windows 10 on a fairly new computer, have never had a problem with WSJT-x before but this version 2.2.0 RC1 does nothing, loaded ok but it does nothing after running

WSJT-X V2.2.0 RC1 gives me. Occasional false decodes such as this.. 150700 -23 2.4 1470 ~ TU; W35CHU IK9MUU R 579 6596 Always the same format TU;….etc And this today: 151245 -24 0.4 2056 ~

im running FT8 on a ic-7100...using a dell 5400 windows 7....i keep getting 'rig control error' i can RX FT8 but not TX ? what can look for to fix it ? albert...............w5apl

Downloaded and installed yesterday. No problems. Made a few Qs and seemed to work fine. My first observation on FT4 is that more signals are decoded on each over. No hard facts to back that up,

On 12/05/2020 19:07, ny2ny wrote: Hi Jay, that looks like an old installation file is remaining, perhaps because you ran the installer while WSJT-X was still running. Please

John, you have set you opinions that this is a WSJT-X problem, you do not seem to understand that WSJT-X uses the Hamlib rig control library for direct rig control. This

It's taking a bit of getting used to, having the received text pop up before the receive cycle (and most of the interval) have completed but getting there. HOWEVER, I don't think I have seen

hello bill, "C:\WSJT\wsjtx\bin\wsjtx and see if any information is printed?" no info on the CMD-prompt but: the same some b4 - wsjt dont start, but still i can see wsjtx in the taskmanager... 73 de

No, it is NOT required! I repeat, N1MM runs the exact same hardware & works perfectly to control the rig! No, the 2 programs, N1MM & wsjt-x don't run at the same time. The wsjt-x 440 selection works

John, Do you have a Kenwood IF-232 in between the radio and your PC? Best, Eric (W1EL)

Can't hurt, Thx Bubba Tim Hero of small cats and defender of undersized lobsters www.bubbatim.com

That's ok; it isn't working either. Keeps saying it's not an executable, etc. Never mind; I guess I'll just give up on ever running DXpedition stations, or having auto-band/freq connections. I am

Layne, do not run utilities that are going to delete files in the temporary files area while programs that are running are using them. 73 Bill G4WJS.

John, it is using a Hamlib test program to open a connection to your rig and to send a fundamental query command to get the current VFO frequency. It will do the same steps

Well I downloaded the 64- bit version of 2.2 and i get an error message on start-up : wsjt-x: ENTRY POINT NOT FOUND. (attached) I close it out, get the same error message the 2nd time, close it out

Hello Bill, Tried from CMD and nothing returned C:\WSJT\wsjtx\bin>wsjtx C:\WSJT\wsjtx\bin> When running from command prompt, no wsjtx.exe running in task manager. I have the cursor back

Hi,I have a problem with 'rigctld-wsjtx' using wsjt-x 2.2.0-rc1compiled from sources on Ubuntu 18.04.4 LTS.Radio is an ICOM IC-7300. Rigctld is started with command "./rigctld-wsjtx -m 3073 -r

Hi Walter and Haris, can you try starting WSJT-X from a CMD prompt as follows: C:\WSJT\wsjtx\bin\wsjtx and see if any information is printed? 73 Bill G4WJS.