Hi Bubba Tim, if the COM port you have for CAT control does not appear under the "Ports (COM & LPT)" section of Windows Device Manager then you have an operating system issue.

On 12/05/2020 12:51, zs6c.ham@... wrote: Hi Geoff, thanks for the issue report, we'll look into that for the next release. 73 Bill G4WJS.

Hi Walter, it may be starting with the window off the screen, this can happen if you last used WSJT-X with a second monitor and now do not have it. Is there an icon for WSJT-X on the

That most of the issue. COM Ports do not show up in the Device Manager. You can only see them in the "Hidden" files. Bubba Tim Hero of small cats and defender of undersized lobsters www.bubbatim.com

Hi there, this has been occuring on quite a few releases of WSJT-X. At the moment I am using v2.1.2 This is what happens a lot. I am ZS6C and there is also a ZS6CR. When I am calling CQ and ZS6CR is

Hello All, the RC1 does not start when i click the icon. for abouth 5 or 6 seconds i see the "sand-watch" from the cursor, after this is nothing... silence... no error.. nothing but i can see wsjtx

Re:- As for support on hamlib, nobody's home and 'they' haven't made an upgrade in years according to; well, just about everyone. It is semi-orphaned. ~ ~ ~ Well. If you get

I agree Bill, The hamlib team are very active at the moment. They are preparing to release 1.4 shortly, but the mod rate is not really slowing down enough to give them a window – too many new

Hi Does the Windows Device Manager show the adapter when plugged in - tried a different USB port ? Tom -- 73 Tom GM8MJV (IO85)

Hello... My setup : --Flex 6300 --JTAlert 2.16.5 --WSJT-X 2.1.2 It works flawlessly I installed WSJT-X 2.2.0.Rc1, and impossible to get it working... Reception and decoding are perfect, but as

Hamlib error: IO error while opening connection to rig. The CAT Control only gives me the option of USB and does not list any COM Ports. Bubba Tim Hero of small cats and defender of undersized

Well Bill, I sent you the Kenwood IC-10 manual that contains the Kenwood TS-440S codes. If they can make a TS-440S driver for wsjt-x, that would be great! Because the regular 440 selection as it is

John, you are very wrong about the activity on the Hamlib project, it is under active development and support is extremely responsive. We are happy to pass on Hamlib issues

Dave, I disagree as the Hamlib is used & distributed by the wsjt-x folks as part of the package. As for support on hamlib, nobody's home and 'they' haven't made an upgrade in years according to;

What was the ‘config error’ ? Tom -- 73 Tom GM8MJV (IO85)

Hi. For the TS440s issue, you need to talk to the Hamlib people over on:-     hamlib-developer@... You'll need to subscribe to the mailing list

Hi Charlie, Yes, I did read that this would happen, but just forgot in haste to download(even the download link said Windows7 or better!) but I didn't "see" it. The previous version of the program

Hi Laurie. I'm the guy who noted issues, but didn't describe it. What I'm seeing is that JTA works until I make a QSO and am prompted to log it. Logging fails, no error message, and no decodes. The

Joe w10 2.2.0 rc1 working fine at-600ii pro flex 6400 jtalert 2.16.5 great job once again thanks for all you do for he ham groups

Hi Bob You are not alone! I saw the same error message on my 32 bit Vista machine. It was due for retirement anyway.... 73 Charlie G3WDG