This should ALWAYS be done. Indeed, ALL equipment that is part of the station should have its chassis bonded to all other equipment in the station, and to station ground, AND every ground in our homes

I've encountered an issue which I have failed to resolve.    I'm using an Elecraft K3S on 160M.  I have WSJT-X configured to work normally and find that indeed it does for what I'll describe as

I had that same error on the MAC, I edited the file and commented out the duplicate.

Hi, The rig is already directly connected to WSJT-X. Is not a real problem, I need to set the VFO-B to the correct mode before. Then WSJT-X connected to the rig, set time by time the frequency

I am using a DRAWS on a Pi as my computer. I am seeing mobile stations move but I am not seeing the data in the View > Incoming Data > TNC Data Only screen. Am I looking for it in the correct

Flex -1500 has bad phase noise.. - don't amplify it.. http://sm5bsz.com/dynrange/dubus313.pdf Robin G1MHU

Agn, tnx... that is what I have been trying but there seems to be no way in WSJT to set up a PTT port to use to key the sequencer that is not the same port WSJT uses to key the rig.....no matter what

Hi Ed, USB communication between PC and TRX is not reliable if the antenna is too close. QRP is certainly a solution but you may want to try this: Connecting the shield of the Notebook-USB connector

When I was using her on my 590sg I ran db9 for cat on her and used USB cable for wait for cat and audio codec. Fake it worked just fine. sent by my LG phone

Mac mini mid 2012 i7 (which I chose because it still had the audio ports, lol) ive had midi setup issues before Using the Mac internal sound card with my FT840. It likes to change from 48k to 44k.

Not sure if this is the right forum to address this issue. I am connecting a TS590SG to the CAT interface of WSJT-X 2.1.2 through the HRD driver of WSJT-X. HRD version is 6.7. Using WSJT-X split

Seeing other caller while in a QSO is common to both FT4 and FT8, and should you wish, you'd simply click on another caller without wasting time calling CQ.

Hi, I've been using FT8 for some years, but since the last to months i've been enjoying FT4. When using FT4 mode right in the middle of a QSO with a station, I sometime receive a QSO call (addressed

Sucess! Thank you so much Bill. # file wsjtx wsjtx: ELF 64-bit LSB shared object, ARM aarch64, version 1 (GNU/Linux), dynamically linked, interpreter /lib/ld-linux-aarch64.so.1, for GNU/Linux 3.7.0,

Bill, ignore my previous,. I remembered how to do it. Compiling now and past the qt_helper stage. 73 N1ESE <jt.tobit@...> wrote:

Thanks Bill, it's been a long time since I last used patch files. Could you please tell me how to apply this? 73 N1ESE

Guys, I am trying out my 2m set-up. I have WSJT-X connected to Fl-rig and Fl-rig connected to PowerSDR for theFlex-1500 using virtual COM ports. I connecting WSJT-X to Power-SDR audio using a pair of

Hello everyone, Tnx for all the feedback. I tried the recommendations about turning the rf down and that seems to have done the trick. At 20 watts the problem is gone. I have some ferrite on the

As Bill mentioned, this problem occurs only on certain hardware, usually older systems (you didn't say what you're running Mojave on). I had this issue a few years ago with a 2011 MBPro (different OSs

Hi Chris, this is an issue reported by several Mac users, it seems to be occurring only on certain Mac motherboards. We don't have a solid solution, various remedies have been suggested, not all work