main@WSJTX.groups.io

Re: Mode Change in split operation

Hi Bill, My Rig is FT-911A. De Settings are: PTT Method: CAT Mode: Data/Pkt Split Operation: Rig VFO-A mode is correcly changed from previosly set (LSB) but not

By IU1JVO · #8563 ·

Re: Compiling for arm64 Issue

Hi JT, well done! What Linux distribution are you using? 73 Bill G4WJS.

By Bill Somerville · #8562 ·

Re: Mode Change in split operation

Hi Giuliano, what rig do you have, and what settings do you have in WSJT-X on the left hand side of the "Settings->Radio" panel? 73 Bill G4WJS.

By Bill Somerville · #8561 ·

Re: HRD and split operation

Hi Hans, I am an HRD user also. My workaround is the opposite: I connect my FT-817 to WSJT-X directly. I just send logged QSOs to HRD Logbook. I use WSJT-X + HRD Logbook only for FT8. You can try to

By Miloš Soukup · #8560 ·

Re: Error in Sound Output: An Error open the audio outout device has occurred??

This should ALWAYS be done. Indeed, ALL equipment that is part of the station should have its chassis bonded to all other equipment in the station, and to station ground, AND every ground in our homes

By Jim Brown · #8559 ·

K3S and WSJT-X on 160M

I've encountered an issue which I have failed to resolve. I'm using an Elecraft K3S on 160M. I have WSJT-X configured to work normally and find that indeed it does for what I'll describe as

By Bob McGraw - K4TAX · #8558 ·

Re: Compiling for arm64 Issue

I had that same error on the MAC, I edited the file and commented out the duplicate.

By Dave Carlton · #8557 ·

Re: Mode Change in split operation

Hi, The rig is already directly connected to WSJT-X. Is not a real problem, I need to set the VFO-B to the correct mode before. Then WSJT-X connected to the rig, set time by time the frequency

By IU1JVO · #8556 ·

Data Logging

I am using a DRAWS on a Pi as my computer. I am seeing mobile stations move but I am not seeing the data in the View > Incoming Data > TNC Data Only screen. Am I looking for it in the correct

By Ed Bloom, KD9FRQ · #8555 ·

Re: 2m using Flex-1500 and transverter.

Flex -1500 has bad phase noise.. - don't amplify it.. http://sm5bsz.com/dynrange/dubus313.pdf Robin G1MHU

By Robin Moseley <robin@...> · #8554 ·

Re: keying sequencer

Agn, tnx... that is what I have been trying but there seems to be no way in WSJT to set up a PTT port to use to key the sequencer that is not the same port WSJT uses to key the rig.....no matter what

By AH0U · #8553 ·

Re: Error in Sound Output: An Error open the audio outout device has occurred??

Hi Ed, USB communication between PC and TRX is not reliable if the antenna is too close. QRP is certainly a solution but you may want to try this: Connecting the shield of the Notebook-USB connector

By dk1wb · #8552 ·

Re: HRD and split operation

When I was using her on my 590sg I ran db9 for cat on her and used USB cable for wait for cat and audio codec. Fake it worked just fine. sent by my LG phone

By Dave Garber <ve3wej@...> · #8551 ·

Re: OSX mojave. Audio switching to built in

Mac mini mid 2012 i7 (which I chose because it still had the audio ports, lol) ive had midi setup issues before Using the Mac internal sound card with my FT840. It likes to change from 48k to 44k.

By Chris KC2BBU · #8550 ·

HRD and split operation

Not sure if this is the right forum to address this issue. I am connecting a TS590SG to the CAT interface of WSJT-X 2.1.2 through the HRD driver of WSJT-X. HRD version is 6.7. Using WSJT-X split

By dk1wb · #8549 ·

Re: FT4 QSO procedure #QSO_practices #FT4

Seeing other caller while in a QSO is common to both FT4 and FT8, and should you wish, you'd simply click on another caller without wasting time calling CQ.

By K7GQ · #8548 ·

FT4 QSO procedure #QSO_practices #FT4

Hi, I've been using FT8 for some years, but since the last to months i've been enjoying FT4. When using FT4 mode right in the middle of a QSO with a station, I sometime receive a QSO call (addressed

By Sebastien VA2SIB · #8547 ·

Re: Compiling for arm64 Issue

Sucess! Thank you so much Bill. # file wsjtx wsjtx: ELF 64-bit LSB shared object, ARM aarch64, version 1 (GNU/Linux), dynamically linked, interpreter /lib/ld-linux-aarch64.so.1, for GNU/Linux 3.7.0,

By JT Croteau · #8546 ·

Re: Compiling for arm64 Issue

Bill, ignore my previous,. I remembered how to do it. Compiling now and past the qt_helper stage. 73 N1ESE <jt.tobit@...> wrote:

By JT Croteau · #8545 ·

Re: Compiling for arm64 Issue

Thanks Bill, it's been a long time since I last used patch files. Could you please tell me how to apply this? 73 N1ESE

By JT Croteau · #8544 ·

Messages