According to pskreporter, N9JMS was heard 4 minutes ago. -- Tad Cook - K7RA Seattle, WA k7ra@...

I do as far as I know. I must be doing something wrong. I take it off of USB-D and put it back on USB with the touch screen. I am not using the SD card option as of yet. I am so lost. 73, Jason

Find a clear place to put your red bracket to TX. You will Recieve everything regardless where you're at. The green bracket will be a specific freq. What band you on? I'll get you on 40m. See you

I have everything working finally, Just don't understand the waterfall part and when and where to TX. I have read several books, and I am still at a loss. I can receive fine. I can TX everything is

You mention that you are et for digital mode (WSJT-X). When you disconnect the computer & attempt another mode: SSB or CW(?) are you reconfiguring the radio for the mode change? Are you using the SD

What band are you on? I did a search for your call, and don't see anything either. -- Tad Cook - K7RA Seattle, WA k7ra@...

Hello, I have WSJT-X up and running fine and have made a few contacts. I have a MFJ-845 hooked up to my rig (IC-7300). I can see the power and SWR when WSJT-X is transmitting. Now if I turn off and

Many thanks for all the replies! I use an IC-7200 with the USB interface. I keep my RF power at about 80% and the USB audio input at about 65%. With the PWR slider of WSJT-X at about 3/4, this gives

Same problem here. I have two Fun Cube Dongles Pro that seem to work with SDRSharp. Connected to two LNA to 432 MHz Yagis for EME. For kicks I copied/pasted the two '5' files as '4' files, rebooted,

I also use a TS-2000 with a Signalink as the soundcard interface. As to power level, I use either the slider on the WSJT-X UI or the TX control on the Signalink. 73 de kb5pgy

I run Kenwood TS2000 but never change the PA output setting from the 100 watt setting on the radio. If I lower power via the PA output control without changing the audio drive level , the PA goes into

Use the Yaesu cable CT62 but check the book. They work. Frank KB3PQT Sent from my Galaxy Tab A

Yes you can. I do the same. Frank KB3PQT Sent from my Galaxy Tab A

You can adjust with the mouse wheel which is pretty easy. de Herb WB8ASI

I hate to say this, but PWR or Power would be the correct control. What radio? Gary - AG0N

https://www.ebay.com/itm/FTDI-USB-CAT-Programming-Cable-Yaesu-FT-857-FT-857D-FT-897-FT-897D-CT-62/161403347303?hash=item259463a167:g:xCIAAOSwmudaGNwM -- Anthony Luscre K8ZT Ohio Section Section

Can someone send me a link to a viable CAT/Liner to USB cable that will work in this situation please? My google searches are coming up with CAT 5 cables and kitty litter, -- John M. Sokol K9JMS

I use the CAT/Linear port to run my LDG AT-897 tuner. Can I run from the CAT out on the tuner? I assume that is the purpose of it. -- John M. Sokol K9JMS

I also have an FT-897D, with SignaLink USB audio I/O and PTT using Data port, and control with CAT cable at the "CAT/Linear" port. My WSJTX settings page, on both MacBook Pro and RaspberryPi installs,

On 28/03/2020 17:24, John Sokol wrote: Hi John, the SignaLink USB is not a CAT interface. It provides audio in and out between you rig and PC and it has a digital VOX circuit