Has anyone experienced decoding on every second pass? On JTDX, every pass decodes consistently. On WSJT-X the first 15 seconds decodes, the second 15 seconds do not and the third decodes again.

Hi, Yes, a bit short sighted approach. I will be looking to buy a YT-847 by LDG, who designed a better tuner which will pass through all non-tuner related commands to the PC. This tuner seems to

Greg, Try setting WSJT-X to Settings/Radio/ Split Operation/NONE. Then set VFO-A to 1908 and VFO-B to 1840. Set the radio to SPLIT. With you power turned down, test by pressing the TUNE button. The

Try XGGCOMMS.com ... interfaces for Yaesu, ICOM, and Kenwood. Very reasonable. Neil, KN3ILZ On 1/16/2020 10:47 PM, David wrote:

On Fri, Jan 17, 2020 at 03:30 AM, Jim Brown wrote: The key is the first part of George's advice to use the PC sound card for system sounds and the USB sound card for computer sound to/from the

Greg: I can verify that the approach described by Bill works perfectly with my IC-7610 so it should also work with your 7300. A key thing to remember is to set the WSJT-X Split Operating option to

Thanks Bill et al - Will play with this over the weekend and see where I land - it looks like many have various ways of making this happen - I just need to see if I can get ONE to work :) Appreciate

On 1/16/20 9:19 AM, Greg Clark wrote: On my IC-7300, I pressed the 'SPLIT' button, then the 'A/B' button, then tuned the RX frequency. I clicked the 'Tune' on WSJTX. My IC7300

Hi. Yep, there is the warning/note on page 91 of the user manual, as found at:- https://www.manualslib.com/manual/381776/Yaesu-Ft-847.html?page=93#manual In the CAT section, no mention of such a

Not the cheapest interface, but looks to have a good chip and isolation. Native Linux support, as well. https://www.tindie.com/products/hb9zhk/digilink-nano/#specs

FWIW, I've never used anything BUT VOX for SSB, RTTY, and other digital modes. The key is the first part of George's advice to use the PC sound card for system sounds and the USB sound card for

Good to know that this has been reported before. As for it not affecting anything, well if I run 1.5kw on EME, the power spike is 1950 w. Amazingly, the beko amp can handle that ok but it's pushing

Bill, Your powers are strong, I've concluded exactly the same after I "Unchecked" the "Start new period decodes at top". And the Band Activity Window no longer disappears. Good Luck with

On 16/01/2020 14:19, Greg Clark wrote: Hi Greg, the advice to use "Settings->Radio->Split Operating->Fake It" which is often given as a way to work a traditional split

Hi Ed, this is a known issue that we don't currently have a fix for. The decodes are printed but are scrolled off the top of the band activity window, you can verify this by scrolling the window

I forgot about the PSK Reporter feed ... not sure if that's a primary feed there for the WSJT-X modes. Neil, KN3ILZ On 1/16/2020 6:23 PM, Chuck Reti WV8A via Groups.Io

My only "reporting" is to PSKReporter directly from WSJT-X, and I've always seen that reflected on HamSpots. Chuck WV8A

Hi, The FT847 is a strange radio. Connecting an FC20 Auto tuner disables the RS232 port without any warning! There is no indication of this on the display, no LED, nothing at all. Yes, there is a

Greg, I am usually driving my TS590 through the HRD cat interface of WSJT-X. But the HRD interface gets confused with the TRX hardware split between 1840 and 1908 (software split of WSJT-X is to be

FWIW .. if you're using JT-Alert the Decodes History Windows will give you that information, along with all the decodes for your current session. Neil, KN3ILZ On