Phil, my understanding is the Signalink is just a audio interface. What device are you using to control the radio? What OS are you using? Jim Bacher, WB8VSU wb8vsu@... https://trc.guru

Is there a way to save my settings other than clone and rename? Is there a file I could save and then restore to do this? I want to set it up with DXLABS but if I make a mess I would like to easily

Hi guys. HAMLIB error seems to be the key. I have not got WSJT-X to run in Ubuntu Linux either. Have spent a few hours now and am very frustrated as I am fairly experienced with MixW and FLDIGI

Hi Phil, I run the exact same setup for WSPR and the rig control is pretty easy and I am happy to share my settings but: Firstly - can I confirm you do have a CAT lead (NOT JUST THE SIGNALINK)

Spent most of the day trying to run wsjt-x, v2.12 so that I could run JT8 and JT8CALL with Yaesu FT-817ND and a Signalink. When first loading up I get a "Rig Control error" box. After checking my

... is tomorrow/Friday evening, NA time: 0200-0230 UTC, 28 December (Friday evening NA time) - RTTY focus 0230-0300 UTC, 28 December (Friday evening NA time) - FT4/8 focus Details below - see you

I have udp port 4739 now allowed through the Windows firewall, but no improvements. Just had WSJT-X running for 45 minutes on 15 meters with many stations decoded, and no traffic on port 4739

Hi Mark, I can't say for sure, only Philip can, but my experience is that spots are "refreshed" on the map whenever a new spot is received. 73 Bill G4WJS.

Jim, Markku ,Bill, many thanks for your replies. Jim, I've started playing with JT Alert and Hamspots and will see how that compares to PSK Reporter. Thanks. Markku, I'm looking at port 4739 with

Hi Mark, reading the rest of your post I think you understand that decodes including a grid square are posted as spots to PSKReport, but just in case, just checking. Calls do not have to be new

Hi Have you opened the outgoing port 4739 on the windows firewall? Markku OH2RA

I’m not sure what it going on David, did you get my email from a week or two ago ? Andy

Mark, I looked at my information in pskreporter, but do not see big gaps. It however is not reporting a significant amount of what I am hearing. I wonder if anti virus software is impacting it? If

to k3unk Andy obrien. hello andy, hope you see this. have been trying to email you via gmail address with no luck. wish to talk with you about your last email to me concerning

And you can check your clock with time.is . If it is within 500 MS then the timing is not your peoblem. Outlook Laptop Gil W0MN Hierro candente, batir de repente 44.08226N 92.51265W EN34rb

can you try other modes, to see if they decode ok. if they do, then I would suggest timing is off, and you should look into nettime or dimension to run at windows startup, to keep you clock

To All, Here is a link to the firmware and project documents for an audio DSP project which works with Software Defined Radios such as a SoftRock or traditional HF transceivers to provide BOTH

Any ‘signals’ on the waterfall? If not then its ‘likely’ a sound card selection issue. W10 is NOT intuitive. You might have to juggle the inputs eg. I select the ‘webcam/micrphone’

Hi All, Philip Gladstone was kind to work with me for quite a while a few evenings ago trying to diagnose my problems with WSJT-X FT8 decodes not getting reported to PSK Reporter, and am wondering if

OM, it is not necessary to create a new socket for every send. What are remoteIPAddress and localPort, specifically localPort sounds wrong, you must send replies to the sender address and port