Here's the .WAV file I can't get JT9.EXE to decode There is one short burst of 2 frames of JT9G-Fast in that 10 second file Andy www.g4jnt.com

hi..mike here ( AA4TN )..having problem with recevie on FT8....no activity on band activity and none on gridtracker on all bands. But when i change mode to FT$ all works great on all bands..nothing

No, Kary, I didn't. I'm sure that the callsign was not in the adi file and btw was the absolutely first Qso with him. Tomorrow I'll perform some test with a dummy installation to investigate... I

Hi Pietro, Correct, WSJT-X will create a new logfile when next QSO is logged. No, only wsjtx_log.adi is scanned by WSJT-X for previous QSOs. Are you perhaps using some 'companion program'  in

The colour codes are not in the adif file, they are in the configuration file. The only thing the adif file does is tell the program which callsigns you have worked on which bands and modes. To be

Yes Kari, I'm sure. v2.5.4 I opened the wsjtx_log.adi file with notepad++ and tried to find the callsign: nothing found. Now I find the qso I had this afternoon with him. And his CQ is green,

All Who Advised, Thanks. I'm about 75% to get everything working. 1. I had to work with the soundcard. I had to turn off the speakers I had on when I listened to music on YouTube I'm a jazz

Hi Pietro, How did you do this cleanup job? What editor did you use? Are yuo sure that you saved the cleaned-up file back as "wsjtx_log.adi" and not something like "wsjtx_log.adi.TXT"  ( assuming

I use a browser called "Brave" - same as Chrome but blocks ads. Especially great with Youtube and their ads. For page/photo copying, if you are using Windoze, just use the snipping tool

I've cleaned wsjtx_log.adi, and I checked that a call (UA6ATG) is not present, but his CQ line is green. In my color setup new call is checked (both first in band and first one whith light blue). I

Additional info: The issue with the tones seems to happen when switching between Tx(x) messages. K7IU

I'm having an issue where after a few minutes, the MSK144 tones are corrupted and I can't complete MSK144 QSOs. When I switch to FT8 the tones are correct and when I click on TUNE I get a good tone.

Not sure what you mean by "have your receive to get signals" > Ron - KJ5XX

It only complains if you'r on 30 meters. Request to developers: Extend the "WSPR Guard Band" feature to work also on 17meters. 73's de Kari, oh2gqc

Hi Frank, at what precise frequency are you trying to listen ? i f you are on a random frequency is almost impossible that you receive anything except you are very very luck :-) First of also set mode

Can you put up your wav file so we can test it? Mike W9MDB

I thought WSJT-X complained if you transmitted over a WSPR frequency. IIRC it used to for JT-65. 73 Phil GM3ZZA Sent from Mail for Windows Sent: 24 September 2022 07:08 To:

make sure you are on USB, have your receive RF set to get signals, go to waterfall and find an active frequency to use scott w7scd aol.com@groups.io> wrote: --

If I go into the WSJT...bin folder and issue the command: JT9 -9 -b G -p 10 -f 700 -F 300 \jt9exe\220926_104120.wav the result is this lot. The file specified is a valid, and correctly decoded,

Bob, Thanks for your advice, however exactly where is the frequency tab? I think I have the same WSJT-x. I had one QSO. He had a +22. 73, Evan