Hi, I am working on my ic-706mkiig.  I got it to work on 20m.  I have no out put on 40m.  My set up uses a CIV and a 13pin connected to the signalink.  I using a Evolve III Maestro Laptop ($60)

-- Brand new to the digie world, pretty sure that I have everything hooked up correctly, except for when I transmit a signal, I can hear it thru the laptop and also thru headset i wear. I havent had

THEN WHAT IT RECOMENNDED

Did you move the jumper block between them? If not, the first is likely either incorrect, or has a bad jumper . . . -- Sent from my Android device with K-9 Mail. Please excuse my brevity.

maybe your screen is not as wide as it needs to be. I can see mine( just right of the tx1-tx6 boxes Dave Garber VE3WEJ / VE3IE yahoo.com@groups.io> wrote:

I found the issue! It was my SignaLink which wasn’t passing mic. My second unit worked perfectly. I’ll deal with bad SignaLink later. I’m getting swr 1.2 tuned with my MFJ yet managed to fry my

CIV "usually" selects the front microphone, so if you have everything else correct, CIV will keep your audio going to the ACC from ever getting to the rig. ( don't select CIV or CAT in the software

Thx for all the input. I gotta a lot of experimenting to see if I can isolate the issue. Plan for today: 1) try different SignaLink just in case I have bad one (unlikely) 2) try mic RJ45 connector

Make sure the 13 pin DIN plug is connected properly. The 13 pin plug has a design flaw that allows it to to be inserted "upside down" (rotated 180 degrees) - pin 13 drops into the keyway and the

I'd put the 706 in FM and tune to an unused frequency at very low power, maybe even on a dummy load, and see if I could hear the tones on an HT. Vy 7 3 Earl KD5XB e e

I would wager that either the audio is not outputting at the level you think it is, or that the '706 is not configured to listen to the correct input . . . (I know my Yaesu's an be odd this way . .

Hi Hank, Yes, all modes including the WSJT tune mode indicate 100 Watts on the power meter. I need to dig into the PW-1 and 7610 manuals to see if there is anything mentioned about this issue. Like

> I dont need Starbucks, but you need a battery powered speaker to listen to the audio input pin on your rig. It's "probably" not there or on the wrong pin. W4DNR > Starbucks gift card to first

Frequency accuracy very important on MS. Initially set your TOL to max wide and try and make sure your partner and you are on the same frequency. Random CQ’s are almost never worth it. Run skeds all

Really makes little difference, since none of the core stuff is distro-centric anyhow. Pretty much has become my own distro, based on Slackware 14.2 . . . (Ubuntu, RedHat, etc. are *NOT* operating

I don't really do mainline distros - they tend to be too downrev, and most of the management tools stink (and all the key stuff is the same on all of then anyhow). I basically started with Slackware

Ubuntu, RedHat, some other version?

What linux version are you running? My Courier on Ubuntu 21.04 has Bold, Bold Italic, Italic, Regular I take it the problem is fixed with another font? Mike W9MDB

How is your SignaLink wired for the IC-706?  Did you get a already-built plugin or wire it youself? PTT Transmit indicates the SignaLink is getting audio.  Lack of power in the rig indicates audio

Michael - Please find my last two messages after the one you replied to, which give full details of what I found. In a nutshell, WSJT-X is calling a system font that does not appear in the WSJT-X