/home/RickO/Downloads/wsjtx /qt5-qtserialport-5.15.3-1.fc36.x86_64.rpm does not provide the required ake Error at /usr/lib64/cmake/Qt5/Qt5Config.cmake:28 (find_package): Could not find a package

Last metadata expiration check: 0:03:08 ago on Tue 21 Jun 2022 11:40:16 AM MDT. No match for argument: Qt5SerialPort Error: Unable to find a match: Qt5SerialPort

My transmit Macros for FT8 have disappeared. How can I restore them?

-- Install# Fedora 36 provides boost-devel-1.76.0-11.fc36.i686, wsjtx asking for boost0devel-1.71 error: Problem: conflicting requests - nothing provides libboost_filesystem.so.1.71.0()(64bit)

This started after I adjusted the PWR slider down. I restored it to full but it never went back into TX.

Output folder: C:\WSJT\wsjtx Output folder: C:\WSJT\wsjtx\bin Can't write: C:\WSJT\wsjtx\bin\Qt5Core.dll

What could cause WSJTx to suddenly stop transmitting? It's a PTT issue not audio. The CAT test and PTT test operate normally. As does TUNE. TIA KD0XX Rod

I reinstalled today because wsjt stopped band hopping. It immediately started the crashing again when it tries to hop. I reinstalled the INI file it crashed a couple of times. How do I send you the

Rick Did you get an answer to your question?  I have a functional 991a setup here and would be happy to share any info I have to help you. 73 Keith/KI5US

When you say "TX still failed" what does that mean?  No power out?  Or power out but nobody answering you? I show you being spotted 18 hours ago so you apparently got TX working for a while. Mike

Tim, I haven't set the radio in split mode.  For a test I tried setting it to split and made sure both VFO's were set to the same frequency.  WSJT-X still decoded and in fact would decode even as I

Willie, N1JBJ To my knowledge Linux Mint does not inject any eq, echo, etc in the standard install and I haven't installed anything like that.  I was dead wrong when I said the software volume

What I meant was that a lot of companies only provide Whinderp drivers, leaving Linux users out in the cold. (I have no idea what Yaesu did, since I don't own a radio with native USB . . .) Signallink

Never said it was wrong, Tim.  Just not the optimal solution.  And, not sure what you meant by the Linux comment....I'm using Uubntu, Mint, Raspian, and Windoze.  All of these work well with the

But then again, if it works, it's not wrong . . . and not every mfg. supports advanced platforms like Linux . . . -- Sent from my Android device with K-9 Mail. Please excuse my brevity.

For what it's worth, I agree. Using a SignaLink to use an FT991A is like driving a Tesla a la Fred Flintstone. If you're having issues sorting out multiple sound cards, suggest Pulse Audio Volume

Unless I am mixing messages in my head, the Hamlib error looked like you were using split? If so, is the *second* VFO also set for USB? If not, you may be transmitting LSB, or ??? which will not be

If you add the "ntpdate . . ." commands I posted to the start and restart batch files (in c:\Prog..x86..\NTP\bin\...) then it will instantly set at boot, and you won't need to do anything. I'm not at

Mike I think at this point you need to verify that you are actually transmitting an FT8 signal. You have a nearby buddy that can get on and verify your signal? Or a second radio that will tune to

From Section 12.1 "AP decoding" of the rc1 local help file.... "Type|a7|, used only in FT8 mode, uses information from the previous Rx sequence." AL, K0VM