I should add the amp should be on the remote CI-V port on the rig. Mike W9MDB On Friday, August 20, 2021,

Please tell us how your USB and CAT ports are set up. Mike W9DMB On Friday, August 20, 2021, 11:50:12 AM

Hi I have not changed the PA firmware. I have not changed the rig firmware. I have updated WSJT-x. If the "feature" in WSJT-x with changing the rig frequency and the PA frequency at the

Thanks to all, its running now. Rich W2KAP

Sounds like your baud rate is wrong. Double check the baud rate on the rig. Mike W9MDB On Friday, August 20,

Hi RIch, if you have the correct USB to serial device selected then the next issue my be you have the wrong baud rate. Check that the USB connection baud rate in your rig's menu

Well... That's an improvement. Now I have a new error :-) Hamlib error: Communication timed out rig_get_freq(2088): freqMainA=0, modeMainA=, widthMainA=0 rig_get_freq(2088): freqMainB=0, modeMainB=,

Well... now I have a new error, but at least it's progress. Dialout <smh> I shoulda known that. New error: Hamlib error: Communication timed out rig_get_freq(2088): freqMainA=0, modeMainA=,

At the command line is dialout in the list when you type groups and press enter? If not you need to add yourself to the dialout group. Type sudo usermod -a -G dialout $USER and press enter. Then you

See if this helps.... https://wsjtx.groups.io/g/main/topic/addition_to_the_linux/83103720?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,400,83103720 Mike W9MDB

I feel like an idiot that I can't figure this out. Rig: IC-7300 to Toshiba laptop via USB running Ubuntu 20.04, fresh install of wsjt-x 2.4 dmesg output: [69126.656469] usb 3-4.1: new full-speed USB

How do you have the amp hooked up to the rig? The 7600 has a separate CI-V port that I would like to think would be behaving correctly. I am planning on using the transceive data in the future and

I forgot to include I am using version 2.4 of the software.

Hi Allan, I'm not sure what you and others with similar issues expect the WSJT-X developers to do. We make no statements on CAT control of ancillary devices that might be connected to your rig. If

Same version of WSJT-X on both I assume? Check File/Settings/Advanced/Tx delay Mike W9MDB On Friday, August

Have had WSJT-X set up for about three weeks, During that time when the system would transmit the radio would change to transmit mode and within a couple of tenths of a second the tones could be

I can confirm similar behavior with my Icom IC-7600 and Expert 1.5K-FA. On version 2.4.0 - no issues. One version 2.5.0 rc 5 (latest) it does not. You can change bands with WSJT-X and the radio

[Snipped] Hi again Derek, here's something else for you to check... I note that in your screenshots of the Microphone Properties you've got the microphone level set to 100%, ie. maximum, in both

Hi Yes Transceive is on. As I said, Cat works fine between PC and rig, but the PA does not shift band when I change band in WSJT-x, only the rig change. This worked before version 2.4

Hi Yes, I had that on another PC. But this worked fine until 2.4 was released. Win 10, IC-7300, SPE Expert 1.3k. USB interface from PC to rig. Normal CI-V interface to PA (from