Hi Jim, one issue with "fake" u-blox boards (note they usually have real u-blox GPS/GNSS receivers but lack on the rest of the board) is that some have insufficiently sized SPI memory chips and as a

On Sun, Jul 4, 2021 at 01:10 AM, Tad Danley wrote: I downloaded WSJT-X v2.4.0 and configured it to work with my IC-7610 - using my settings for N1MM+ as a guide. I am able to decode stations using

Look at ICOM knowledge base for documentation on digital settings. For the IC 7300 setting power to 100% is recommended then use TF8 slider to set power out to desired. Green ALC is ok, just don’t

Hello. I have same problem with same library in Ububtu 18. I had wsjtx 2.1.2 running fine on ubuntu 18. Then I went to update to 2.3.0 and it just never launched, although icon was there. I did

Re time1 vs time2: I am running the latest release of Meinberg and can state time1 does what it is supposed to do. If you are running an older version you should upgrade because many other bugs have

I used HRD for many years(2010 al;l versions) and had no troubles, and none since logging since adding of WSJT-x FT8 and JTAlert a couple of years ago. Use what you like but avoid trashing

Outlook Laptop Gil W0MN Hierro candente, batir de repente 44.08226N 92.51265W EN34rb

Turned off the secondary UDP and problem solved. Thanks.

>the wsjt freq window turned red. Mike, No problem, as the QSY frequency was not defined as a working frequency for the band/mode. I think that it is just a reminder. 73, Reino OH3mA

Tad The 7610 Needs to be in mode USB Data., select USB and then select Data. 73 Derek G8ECI

Yes. I occasionally get this with my Flex 6400. I think the problem is with DAX (I’m on version 3.12ish). When the problem crops up it’s usually when I’ve been connecting DAX to different

I've built a few NTP servers with various serial GPS's on the Pi ZeroW and 3B+ using PPS. Not hard to build and they support the whole Field Day group with a little low power box. We used two on Field

Tad, I assume you are using single USB-cable between your rig and computer. Try setting PTT method to "CAT", TX audio soutce to "Rear/data" and mode to "Data/Pkt". You also need rig menus to set up

On 7/3/2021 9:26 AM, Jim Pennino via groups.io wrote: Bob - wd6dod

Hi Tad, you have no Tx because you have selected PTT Method as VOX in WSJT-X, that basically does nothing and expects the rig or audio interface to do the necessary. For your setup you should select

That station is an IOTA expedition with some very experienced operators. It’s a rare island, QSY! https://na-234.com You will see FT-4 and FT-8 around 7.047. They’re also very near the boundary of

HRD logs whatever is sent to it. Only one program should be logging the contact to HRD. It seems to me that is your problem. 7 3 Bob N2SCJ

I’ve been using WSJTX and JTAlert logging to HRD for over 2years and have never had a problem. Have I just been lucky? Bruce, K0SON

I downloaded WSJT-X v2.4.0 and configured it to work with my IC-7610 - using my settings for N1MM+ as a guide. I am able to decode stations using FT8 on 50.313 but the radio will not key the

I downloaded WSJT-X v2.4.0 and configured it to work with my IC-7610 - using my settings for N1MM+ as a guide.  I am able to decode stations using FT8 on 50.313 but the radio will not key the