>the wsjt freq window turned red. Mike, No problem, as the QSY frequency was not defined as a working frequency for the band/mode. I think that it is just a reminder. 73, Reino OH3mA

Tad The 7610 Needs to be in mode USB Data., select USB and then select Data. 73 Derek G8ECI

Yes. I occasionally get this with my Flex 6400. I think the problem is with DAX (I’m on version 3.12ish). When the problem crops up it’s usually when I’ve been connecting DAX to different

I've built a few NTP servers with various serial GPS's on the Pi ZeroW and 3B+ using PPS. Not hard to build and they support the whole Field Day group with a little low power box. We used two on Field

Tad, I assume you are using single USB-cable between your rig and computer. Try setting PTT method to "CAT", TX audio soutce to "Rear/data" and mode to "Data/Pkt". You also need rig menus to set up

On 7/3/2021 9:26 AM, Jim Pennino via groups.io wrote: Bob - wd6dod

Hi Tad, you have no Tx because you have selected PTT Method as VOX in WSJT-X, that basically does nothing and expects the rig or audio interface to do the necessary. For your setup you should select

That station is an IOTA expedition with some very experienced operators. It’s a rare island, QSY! https://na-234.com You will see FT-4 and FT-8 around 7.047. They’re also very near the boundary of

HRD logs whatever is sent to it. Only one program should be logging the contact to HRD. It seems to me that is your problem. 7 3 Bob N2SCJ

I’ve been using WSJTX and JTAlert logging to HRD for over 2years and have never had a problem. Have I just been lucky? Bruce, K0SON

I downloaded WSJT-X v2.4.0 and configured it to work with my IC-7610 - using my settings for N1MM+ as a guide. I am able to decode stations using FT8 on 50.313 but the radio will not key the

I downloaded WSJT-X v2.4.0 and configured it to work with my IC-7610 - using my settings for N1MM+ as a guide.  I am able to decode stations using FT8 on 50.313 but the radio will not key the

Overload anywhere the signal is audio will generate harmonics and intermod. This can happen between the detector in your radio and the WSJT-X decoder, and between the other station's WSJT-X and his

I downloaded WSJT-X v2.4.0 and configured it to work with my IC-7610 - using my settings for N1MM+ as a guide.  I am able to decode stations using FT8 on 50.313 but the radio will not TX.  I have

Hello Philip, What I observed then isn't happening now. And it doesn't occur all the time. At the moment, 6m Band dead here in KY and the WF has but one lad calling CQ. He's a -11. Signal looks

Hello Bill: The NB, as it is now, wasn't activated. I believe it was still NBOFF as I usually leave it. The "next" time I see received signals like that, I will screenshot the UNO settings/faces as

Agreed. I actually went the OTHER way (HRD to DXKeeper) to get away from things just like that. And also the pretty poor support of their software, despite expecting you to pay for it. My advice

Go to this YouTube video YouTube.com/watch?v=C7f-RZOnmDs

Watch this YouTube video. https://www.youtube.com/watch?v=C7f-RZOnmDs Sent from Mail for Windows 10

I was having trouble running WSJT-X JTalert and HRD also until I found a video on how to change the HRD log book data file to and MariaDb database and all the problems went away. And put the right