If Settings>Reporting is enabled, PSKReporter should show you as monitoring station (always normally ...) -- --- Christoph Petermann DF9CY JO54al (Baltic Sea Coast) 7 MHz Dipole @9,5m - 400w 50MHz 6

If Settings>Reporting is enabled, PSKReporter should show you as monitoring station (always normally ...) -- --- Christoph Petermann DF9CY JO54al (Baltic Sea Coast) 7 MHz Dipole @9,5m - 400w 50MHz

I’m trying to set up a Yeasu FT-450D and a Windows laptop for Field Day and I’ve hit the most intransigent problem I’ve ever seen with WSJT-X and Windows. Laptop is an old Asus Q500A running

Hello Bill Yes, of course I did that - so here it is: "JJ" = read JTDX-files with JTDX "JW" = read JTDX-files with WSJT-X etc: 10:48:30 - JJ 2 dec. - WW 3 dec. - JW 3 dec. - WJ 2 dec. 10:59:15 - JJ

Yes, I did. -- Jeremy G7BHB

Neither is a required suffix in US or possessions, but both are legal. US ham licenses are not tied to an operating location, since around the 1970s. The location on our licenses is the location where

Goto: https://time.is and check your computers time. Jim Bacher, WB8VSU wb8vsu@... https://trc.guru

OM, I will assume you are running MS Windows, have you followed the suggestion in the User Guide installation instructions to install a third-party time synchronization

Hi Hans, you are the first to report that issue as far as I know. Other than making sure your distribution packages are all up to date I don't have any suggestions. 73 Bill G4WJS.

Hi Frank, receiving station reports are sent to PSK Reporter regardless of whether decodes suitable for spotting are received, all you need do is enable PSK Reporter spotting in "Settings->Reporting"

Hi Pietro, do you have the option "Settings->General->Allow Tx frequency changes while transmitting" checked? 73 Bill G4WJS.

With v 2.4.0 when the watchdog jumps up my FT817 continues to transmit and an error appear in the frequency window Furthermore after a few minutes without any tx the frequency window become red with

I am operating a TransAtlantic VHF SDR Beacon Monitoring station here in St.John's NL GN37. The callsign for this 2M receive only station is VO1FN. Since inception in May there has been one decode of

Compiled WSJT-X from the latest source code on a Kubuntu 20.04 machine, connected to my (for me new) TS-2000. Everything works, except for the delay when e.g. double clicking a call in the band

I have not run WSJT X in about 1 month. I fired up my IC 7300 and ran WSJT X....everything seems to be looking like its working...I see signals on waterfall....the level meter showing about 60%. But I

Hi Joe, I also noted that Q65 behaves differently than the other modes in the 77-bit family. Q65 leaves out my call e.g. in message “WB7LYJ/R OH3MA 73”, when it automatically generates that

I followed all the instructions received and now it is working without power output interruptions. Thank you to everybody. 73, Yvon AE7YD Monday, June 21, 2021, 5:20:43 PM, you wrote: I've also seen

Hi Chris, thanks for those .WAV files. I was under the impression that you had more information about which ones failed to decode certaon messages. If you do have a list of messages not decoded for

Hi Joe I also managed to invoke this "defect" last night on FT8 using V2.4.0 I manually changed TX5 to say "KV4BV JO02 73" but the actual transmitted message was "KV4BV JO02 60" as seen on my own

Thanks for the prompt review and response, Joe. WSJT-X just keeps getting better! 73, Jim @ K5ND