Tim, A good SWR does not mean you will have no RF problems. Try transmitting into a dummy load or power right down. You are describing a "RF in the shack" symptom. 73 Alan G4ZFQ

I had a slightly different problem with HRD and WSJT but it sounded somewhat similar. The problem seemed to be on their side. I suggest sending a request to HRD for support. It took them a while to

Just an update. I do have some SWR issues, particularly 6 meter so I am working on that (or will soon). However, on 40 meters, where I do not have any SWR issues, I must be setup correctly in terms

I just installed 2.4.0 - I use a K3 with CAT & no external hardware & WIN10Pro2004- I immediately noticed the same issue with a 2 sec delay in TX on both 'Tune', WSPR & FT8. The

Ok, I did that and now have full output power from the radio, BUT, I also have the transmit tone emitting from my computer speakers that is SO loud my dogs are howling, lol. The problem is if I lower

Have you checked the audio levels? https://wsjtx.groups.io/g/main/topic/setting_windows_wsjt_x_tx/75435187?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,0,75435187 73 Roger G4HZA

Bill, finally got out to the shack today to check on this. Thanks for your help so far. So I changed the radio tab in Power SDR CAT ID to "Power SDR" where it had been TS-2000. then I brought up JTx

Anyone have any idea why TX power output would be extremely low using WSJT-X 2.4.0 with an IC-7300 and Win4Icom software. The rig by itself is putting out full 100+ watts but when transmitting through

Try moving to v2.4 which has just been released. Neil, KN3ILZ

I decided to revert back to WSJT-X V2.1.2, so pleased to say it is all back to normal.

This is the error message when in transmit mode on the main screen of wsjt-x Hamlib error: Communication timed out kenwood.c(577):kenwood_transaction return(-5) kenwood.c(1604):kenwood_set_freq

Wrong groups.io list OM, try hamapps.groups.io for JTAlert support. Neil, KN3ILZ

I have recently upgraded from v2.12 to v2.3 on a Windows 10 operating system. While v 2.12 worked perfectly there is a Hamlib error with communication with my radio a TS870. When testing "cat

Strange Bug to report. Display issue with JTAlert menu bar window when using Ham Radio Deluxe LOG SYSTEM: Processor: i7-4770k 3.5Ghz RAM: 16.0 GB OS: 64-bit Windows 10 Pro Version 20H2 OS

The new version is currently in the testing repo. I don't know why hamlib 4.2 is currently not available on F34, I built that myself. It may not matter but there were problems with earlier hamlib

Hi JD, our production system is still on Fedora 33, it will probably be upgraded for the upcoming WSJT-X v2.5.x releases. You should either build from sources, or wait for our RPM style package

I upgraded my Linux box to Fedora 34 (from 33) and then tried to upgrade the WSJTx to the General Availiablity release WSJT-X 2.4.0 It would not load, and the following error appeared: - nothing

Gary, Thank you for your response, however I was referring to the fact that 2.4.0 GA has a rig control bug - a severe one. I was referencing a bug fix for the GA and not a replacement for rc4 Best

Hi Bob, yes I mean the PowerSDR/Thetis rig selction in WSJT-X "Settings->Radio->Rig". What is the error message, including details, when you use that? 73 Bill G4WJS.

Hi Dwight, 50.275 30A is pretty standard. I would like the try to work you from CN81 in Yreka. A bit of a challenge since I have 6’000’ + mountains between you and I and am very close to them.