I share your pain, the problem I have is that the list you show above is not scrollable and so some entries appear below the screen edge and are not selectable without guesswork. -- Brian G8SEZ

Thanks for the clarification Bill, I didn't realize this. Perhaps I read it in the manual years ago and forgot, no idea. I no longer have my FT-DX3000. When I did, it was correctly set to "Fake it"

Hi Rick, the HRD/split issue has been reported here several times. The HRD team was asked several times to improve the driver but no success. Finally I gave up to use HRD with split. 73 es GL, Hans,

Hi Bill & all. Couldn't be also a timing error caused by hamlib (when set to use "Ham Radio Deluxe" which means sending commands via network rather then on Cm port) ? I agree with : when HRD is used

There is external software that interfaces with WSJT-X that does this and more. Gridtracker and JTAlert. Have a look at them. Jeff Townsend WB8LYJ/R

Could that be dark style https://www.physics.princeton.edu/pulsar/K1JT/wsjtx-doc/wsjtx-main-2.3.0-rc1.html#DARK_STYLE You add --stylesheet :/qdarkstyle/style.qss to the command I use it for a

It is available ... the setup is covered in the User Manual: https://www.physics.princeton.edu/pulsar/k1jt/wsjtx-doc/wsjtx-main-2.3.1.html#DARK_STYLE Neil, KN3ILZ On

Hi all, My thanks to those who responded with constructive comments. Given their structure, I had hoped it would be realised that the two callsigns I used as an example would be recognised as being

MS took out my Nvidia GPU but my tx problem predates it by a bunch. I don't think they are related in my case. I have learned to do a test tx after changing bands. Bob - wd6dod

a dark mode would be so nice to have...

Hi, There are 2 , possibly more, issues here. 1) The tune issue has been addressed on here and is hopefully being fixed next release. If you hit tune and then decide to call CQ or answer someone

Hi guys, I'm pretty sure this is a WSJTX issue since I had the same problem under Win7 with CreativeAudio sound cards and I have exactly the same problem on now that I've switched to Ubuntu 20.04 LTS

Hi all, I've just setup WSJT 2.3 on Ubuntu 20.04.2LTS and everything is working fine but I was wondering if there is a way to make WSJT only see active audio devices or better yet, only

Hi Bill, I am interested to see where this leads. I have the 101D and have to run split as none or my TX is around 500Hz higher than what the waterfall says it is. I can't be sure but I think this

John, Yes, having the transmit move around, (assuming you have some form of split turned on), is normal. Your rig will shift around in transmit frequency, (slightly, Hz., not KHz.), depending on

Hi John, it is normal for WSJT-X to shift the Tx VFO dial frequency according to the Tx audio offset you choose, it is done to ensure your signal is as clean and free from audio harmonics as

You should NOT turn split off. You need Split or “Fake It” to ensure a clean TX signal, unless you only every TX above 1500Hz. 73, Paul G4IJE.

Mine does as well, as it should when the audio component of the sent transmission falls outside the optimal passband of the transceiver. This is to ‘push it back’ to where it is within said

Fred, the way WSJT-X uses a different VFO dial frequency for Tx is not a problem that needs solving, it is an important feature that ensures your signal is as clean as possible, which also allows you

John, Regarding the shift, the VFO frequency remains constant on my FT-DX3000 between transmit and receive. I would check two things: 1) Make sure you aren't in Hound Mode. 2) On the settings tab,