North Korea, "ABC", Kim Jong-un ...... Wake up and smell the coffee. Sorry. -- 73 Ron W3RJW FTdx-5000, Timewave Navigator, WSJT-x 2.4.0 rc4, JTAlert 2.50.1, HRD Deluxe v6.7.0.357 FTdx-3000,

do you have additional software for time sync. check your clock at time.is to see if your clock is off greater than 2.5 seconds ( critical) try using dimension4, meinberg, or any other available

A shift of 500Hz (that’s HERTZ not KILOHERTZ!) is completely normal. It allows the program to generate the tones at a higher frequency to keep harmonics outside the TX passband. 73, Paul G4IJE.

John Are you sure it shifts 500Khz !! thats going put your signals way outside any band we have I fear !!! Not being an expert, but the only time I have noticed a similar problem with decodes, is that

I agree with you and Peter, it is definitely not RFI. I lost the output with 1 or 2 watts output from my FT-857 and even lost it while transmitting into a 50-ohm load. Sometimes I can switch back

Everything was working great, WSJTX, JTAlert and HRD LogBook. Then there were no decodes the next operating session, no Windows updates to interfere. I hear and see loads of signals but no activity is

Hi I have over the years used a RPI for WSJT-X, mostly for FT8 and MSK144. The "speed" of the RPI is on the margin but when #4 was introduced I had no issues to run WSJT-X in deep mode

It's important to realize that distortion can be produced at multiple points in the audio chain between detector and A/D converter, and, as suggested by a post in this series, even in the IF due to

Hi Bill, Regin hope you don't mind me replying. I have discussed this very briefly on ON4KST chat. In these chats we are asking Regin to try q65 so I think he is trying to install 2.4 or later

False decode

Here is an example of P5 called upon, decoded on 50.313 MHz with FT8 at my QTH locator JP50: 131845 -24 -0.2 1455 ~ P5DUK/P I68NZL/P EC53 But at such a low -24 dB signal/noise ratio it is

As Bill said, only QRZ and CQ is watched for. You also don’t say whether you decoded the P5 or not. One thing for sure, if you don’t hear him, you can’t work him and it shouldn’t say

is there activity from p5 at all, or was this maybe a false decode? why have an alert for a station you are not hearing?? Dave Garber VE3WEJ / VE3IE

Hi Wes, P5ABC would have shown up earlier for you, when calling GW3DEF, and would have been highlighted. Good luck with the pileup! You might also want to look at JTAlert. 73 -- Larry -- W1DYJ

On 12/05/2021 14:15, Rick I2BRT wrote: Hi Rick, when HRD is used as a proxy CAT control server all CAT commands are handled by HRD. 73 Bill G4WJS.

Hi Don, the WSJT-X default is not to save .WAV files, you must have enabled it at some point. 73 Bill G4WJS.

I AM an expert on RFI, and I find the "knee-jerk" blame it on RFI unhelpful when there's no good reason to blame it based on the limited symptoms provided. Yes, many hams DO fail to do proper bonding

Roger, That reminds me of a USB audio problem I used to have. If there is a temporary interruption in the USB audio then it seems WSJT-X stops. A restart brings it back. The disconnection was likely

Not for all of us. Happens after a band change. Bob - wd6dod On 5/12/2021 2:54 AM, William Smith wrote:

Thanks for your input, Bill. As it turns out I had almost 40,000 saved wave files along with a huge amount of backup files from Ham Radio Deluxe. My C Drive was nearly plugged solid. Once I addressed