Boris It is inevitable, if you want best decoder sensitivity. 99% of false decodes are obvious and can be discarded immediately upon inspection. False decodes are a feature, not a bug....if you

Hi Bo, Not discouraging at all. Thank you for your time and assistance. This is all new to me, so it all helps. As you may see in an earlier post, I had an incorrect frequency for transmit, adjusted

Hi Reino, Thank you for your feedback and time. I had the transmit frequency incorrect in the Arduino firmware that controls the 5351...I have since corrected to transmit on 14.0956 MHz and there is

Thanks for the reply, Bill. I was able to rectify "most" of the issues, but one still has me stymied: no audio! I set the interface up as directed by the manufacturer, but there is no audio. I can

Hey Don... I too have been using using the Rigblaster with audio problems.. I got a Signalink USB and plan to use that with my TS-2K.. would you send me a few screen shots of the options you use for

Hi Boris, Short answer is no. A bit more practical answer is that is depends on many issues and usually a careful balancing is needed. I take just one issue that is a limiting factor. It is how many

FYI - that's v2.3.1 !!!-- 73 - John - N7GHZ

Better to switch to FST4W, which is superior to WSPR, and which the developers intend to replace it. Same problem with FST4 on 160M -- sure wish it would replace FT8. 73, Jim K9YC

Hi Reino, I got it. Is it possible to eliminate false decoding in the program or is it an inevitable effect of a deep level of decoding? 73 Boris UX8IW -- Борис Романов

On Fri, Mar 26, 2021 at 04:34 PM, Bill Somerville wrote: ...are you sure it is WSPR? FST4W signals can often be found near the WSPR sub-bands. 73 Bill G4WJS.Bill, I guess I should experiment by

OM, have a look at this: https://wsjtx.groups.io/g/main/topic/wspr_cannot_find/78651635?p= upgrade  to the latest version 3.3.1. 73's de Kari, oh2gqc

I am translating the v2.3.1 User Guide. In section 17.2.10, Table 7 quotes the FST4-15 Keying rate (Baud) to 16.67 baud, whilst the Bandwidth is quoted as 67.6 Hz. Should that be (16.67 x 4 =) 66.7

I am using Yaesu FT-450D + SCU-17 WSJT-X v2.2.2. using CAT for piloting the rig Band Hopping marked in WSPR Band Hopping table I selected which band I want to use and when I got error telling not

linuxham@groups.io | Home 73, Reino OH3mA Isn't there a FLDIGI support group? It has nothing to do with WSJT-X, although it will work with it. Neil, KN3ILZ

Yes there is a FLDIGI support group... Just mailed in the wrong group and I'll try to delete the message. Sorry for any inconvenience. -- Bruno Peticone, IU0OAD

Isn't there a FLDIGI support group? It has nothing to do with WSJT-X, although it will work with it. Neil, KN3ILZ On 3/30/2021 8:34 AM, Bruno Peticone via groups.io

Hi Boris, You may also disable AP and will get less that kind of false decodes of type a2. Unfortunately due that you will miss also some real decodes due that. 73, Reino OH3mA PS. I would

TU Bill ! -- jay ny2ny

Hi Bill, I understood you. In previous versions, I used the normal decoding level. In this version, it is deep: There was false decoding again today: Returned to normal decoding level. In this case,

Hi Not to discourage you, but there is about everything wrong there can be with your signal: - drifting, J-shaped instead of vertical lines. H/W problem - wobbly, the same symbol goes back and forth.