Thanks for version 2.4.0-rc3. In the v2.4.0-rc3 User Guide, the illustration of section 10.1.5 Mode Menu shows the v2.3.0 Mode Menu, including QRA64 and ISCAT, both to be deprecated in v2.4.0. I

I can duplicate this in 2.2.2 by starting everything from DXLabs launcher even when JTAlert is started last. Killing JTAlert and restarting will fix it. Until I realized what was going on I

I noticed the other day that WSJT-X(v2.3.0) is not recognizing calling stations in response to my CQs. In fact, it just continues calling CQ in spite of there being 1,2,or 3 callers showing up in the

Since he stated that he reinstalled after a crash, its very possible that the WSJT settings file didn't make it. That may be why the colors are wrong, not because of the version.

One thing to check is your computer time. It has to be pretty accurate or you'll get no decodes.. You can check your system time accuracy by going to https://time.is/

OK, I do see that but I see nothing that says F1 has to be the initial frequency, talking only about ramped-FSK mode because, per the datasheet: The purpose of ramped FSK is to provide better

Hi Ken, that device requires the F1 register be the lower frequency when using *ramped-FSK* mode, in non-ramped FSK mode the two registers may be either higher or lower

In other words, do what Bill said. I have to believe that the makers of this device intended such a need as this otherwise, this would be a pretty useless feaure. Ken KC6PUQ

Hi folks. I am jumping in because this looks interesting and may be something I want to look at more closely.. I want to comment that I am not clear on the understanding of F1/F2 as expressed in this

Yep RC3 it stops dead after a long run, not seen this before on any previous version Peter M0PWX From: Kenneth Williams By going through the sequence of disabling 'Monitor' then

On 16/03/2021 15:33, Buddy Morgan via groups.io wrote: Buddy, which WSJT-X version are you running? 2.4 is not sufficiently specific, there have been three separate release

Since I downloaded 2.4, I have had problems getting my FTDX101MP to work with the software. I have got it to work a few times - I have no idea how I did it. 2.4 works fine with my IC 9700 and my IC

I would like to report that I solved this problem. On the install file for Windows 10, go to properties--Security tab. There will be a notice at the bottom "This file came from another computer and

Meinberg also running here on Windows 10 computer. Within 2msec at the moment. Geoff G4FKA

My machine: Windows 7, 64-bit WSJT-X Version 2.4.0-rc3 Current mode: FT8 By going through the sequence of disabling 'Monitor' then re-enabling 'Monitor' some time later, the waterfall display will

Dave, Thanks, I just wondered, last update 2008, only up to W8, no obvious recommendation from Meinberg. 73 Alan G4ZFQ

Same here, try restarting JTAlert, worked for me but there are other problems with 2.3. I reverted to 2.2.2 and all my problems went away. Bob - wd6dod On 3/16/2021 5:02 AM,

No Bill, there is a bug. dod On 3/16/2021 6:37 AM, Bill Somerville wrote:

Hello all, Bill - technically speaking what you wrote is true, but not really... The Cyan (lt. Blue) is "NEW CALL", & once worked, the call falls through the list & will show up as Green; therefore a

Been having a problem off and on...I can see a lot of activity in the Waterfall, but nothing is showing up on the Band Activity Window...I can TEST CAT and that works, I can Enable TX and I see my