On 21/01/2021 19:06, km6hk via groups.io wrote: Hi OM, WSJT-X uses the system fonts, select them from the font choosers in "Preferences->General". 73 Bill

I have tried to install the fonts.txt file but it has no effect. On macOS Catalina Version 10.15.7 it is in directory: applications > wsjt-x, -perhaps that is not the correct directory?

On 21/01/2021 18:50, Bill Somerville wrote: Hi Ken, just a thought - is COM18 the CAT port for your rig? 73 Bill G4WJS.

Hi Ken, I have double- and triple- checked this works. If you have working CAT control and band-hopping is enabled the user_hardware script works. Is it possible your anti-virus software is

FTDX-3000 owner here if you need more testers. 73, Bernd - KB7AK

Hi Bill, 'where' response below, plus response if I run the command (all works); Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:\>where

Hi Scott, Also common mode choking on the CAT cable may help on RFI. Multiple turn through a ferrite ring could do the job. 73, Reino OH3mA

I do have Settings->Radio->Mode->Data/Pkt" checked in WSJT-X.i have no issues on 40m or 80m. It's been recommended that I move my RF choke from inside the house to the antenna feed point. I'm going to

Hi Scott, do you have "Settings->Radio->Mode->Data/Pkt" checked in WSJT-X? 73 Bill G4WJS. On 21/01/2021 16:58, Scott Downard wrote:

Thank you for the feedback. I tried with the power all the way down, but it's still not working. I do have an RFI choke, but it is close to the radio. I may need to move it outside to the

Hi John, do you have the correct mode selected in the "Settings->Radio->Mode" panel? 73 Bill G4WJS.

I have an FT-990 running HRD Version 6.7.0.323 for rig control. WSJT-X v2.2.2. When I click on the band selector box the radio responds correctly all except for the Mode. Whatever mode the radio was

Hi Scott, rig control issues that only occur on some bands are invariably due to RFI issues. Try reducing power to minimum, using a diferent aerial, or dummy load to verify if RFI is causing the

When using WSJTX to operate FT8 on 40, 80 and 160 meter, I have no issues. When I try to transmit on 30, 20, 17 and 15m, I get a CAT error. It either shows that it cannot verify VFO or PTT state and

The Antenna tuner is off. I would think if that was the case then even if I changed a single band I would here it. When I change the band manually I basically here a single click which I assume is

Hi Bruce, we have example .WAV files that decode as many as 60 signals. Of course propagation variations and geographical distribution will mean that many more stations can be actively engaged in

Jim take a look at this site. http://www.totalcardiagnostics.com/support/Knowledgebase/Article/View/92/20/prolific-usb-to-serial-fix-official-solution-to-code-10-error It's how I resolved my issue

I have a fake PL2303 USB to serial lead for the FT857. I didn't know it at the time as it ran fine for several years until the update stuffed it for me. I followed these instructions to install the

With the ever-increasing popularity of the FT8 mode, there are times when I am decoding in excess of 36 stations on a single channel (JTAlert display slot maximum). And I am practically forced to

If your rig has an internal ATU, it will follow the band selection. Bypass the ATU and see if the “relay clatter” goes away on band change. Best Regardses from eastern Maine, Eric (W1EL)