Better yet, how to make 2.2.2 NOT launch the radio? Gary - AG0N

Hi Patrick, put the attached file into your WSJT-X log files directory ("Menu->File->Open log directory"). 73 Bill G4WJS.

I'm running v. 2.3.0 rc3 - how do I have WSJT-X launch my radio as it did before with 2.2.2? Thanks. -- 73, Patrick, W6AJR

Since installing 2.3.0 rc3, I no longer see my radio being automatically turned on by WSJT-X - how do I make that happen again? -- 73, Patrick, W6AJR

Hi Rick, I am not sure what you are doing, but I just purchased an IC-7610 and am using the USB connector to access the Audio Codec for WSJT-X. My setup allows WSJT-X to set the IC-7610

Hi Rick, if you change rig to USB-D2 does WSJT-X change it back to USB-D1? 73 Bill G4WJS.

Thanks of reply, Bill. I have tried the V2.3.0 and with the IC-7610 as the selected radio, I see the same thing where WSJT-X calls USB-D1. I would like for it to call USB-D2. Oh well, looks like

V2.2.2 crashes when using band hopping for me. 73s Bill WA8VIH EL98

Bill, Thanks for this. I had a chance to try this today and it did solve the problem I was having with trying to use a VSPE splitter to get the result I was looking for. Now FTDX-101MP, SDRuno/RSPdx,

On Fri, Jan 8, 2021 at 05:44 PM, Rick wrote: The Data/Pkt Mode command of WSJT-X sets the IC-7610 to DAT1 mode. There are three data routes in the IC-7610. DAT1 is assigned by default to the

Thanks for the comments Bill. As I don't use Windows for this stuff I have never tried it. I tend to run Window with the noises turned off anyway but this is good to know. I think most people are

On 08/01/2021 17:36, Rick via groups.io wrote: Hi Rick, as of WSJT-X v2.3.0 RC3 Hamlib should be trying to keep the selected configurable filter selection, like the Icom ones,

The Data/Pkt Mode command of WSJT-X sets the IC-7610 to DAT1 mode. There are three data routes in the IC-7610. DAT1 is assigned by default to the accessory plug in the rear, where DAT2 is assigned

On 08/01/2021 17:16, Alan G4ZFQ wrote: Hi Alan, you are OK with that latency using WSPR I think, with FT8 the newest decoder with multiple sections of decoding passes latency

Bill There are now settings that enable audio from a single program like a browser be sent to any other audio device. Works instantly. Windows has to eventually come up with something useful.

On 08/01/2021 16:51, Alan G4ZFQ wrote: Hi Amos and Alan, if using Windows <10 then you can make the VB Cable input the default audio output device then restart your web browser,

Bill I got it! It is working now. I did use the WIN10 built it mixer to connect the output of the internet explorer to the input of VAC Many thanks Amos 4X4MF

Amos What operating system are you using? This is possible in Windows 10. 73 Alan G4ZFQ

Hello I still cannot get the WSPR band hopping to work ( SINCE 2.2.1). Set up is Win 10 20H2 Rx only with co-installed SDRUno using Kenwood TS480 for CAT interface via VSPE. Manual frequency change

Thank you Bill OK, I got you, using the rig name and the CAT of my Flex Radio, I did connect driver CABLE Output (VB-Audio Virtual Cable) to the soundcard Input. I am listening now to Wide-band